Truran, Johnson, Overman and Kirk on blast, blowing engines, pigs and puddling
Books The Iron Manufacture of Great Britain, Blast-Furnace Construction in America, The Manufacture of Iron, The Cupola Furnace
Sources:
- W. Truran, The Iron Manufacture of Great Britain, theoretically and practically considered, second edition, revised from the manuscript of the late Mr. Truran by J. Arthur Phillips (London, 1862), 454 PDF pages. Page numbers below are the printed folios; the PDF page is the printed page plus 26. The text layer is good except in the plates and tables; the Dowlais engine tables (pp. 189-191) were read from the page images. Later printings (1863, 1865) were not read.
- J. E. Johnson Jr., Blast-Furnace Construction in America (New York, 1917), 441 PDF pages. The PDF has no text layer. The text was read from archive.org's own OCR of the same scan, and each printed page below is taken from the running heads of that text, so it can be one page out. 1917, American practice, a cross-check only.
- F. Overman (1851), pp. 201 and 206, read for the pig bed only (Overman's blast chapters are in the Overman blowing note).
- E. Kirk, The Cupola Furnace (1899), PDF p. 267, one sentence on foundry pigs.
Facts are the books'. INFERRED marks arithmetic or a reading added here. Metric is converted here (1 ft = 0.3048 m, 1 in = 25.4 mm, 1 cu ft = 0.02832 m3, 1 psi = 6.895 kPa, 1 cwt = 112 lb = 50.8 kg, 1 ton = 1016 kg, 1 lb = 0.4536 kg); the books give none. Truran's "yard" of capacity is a cubic yard (0.7646 m3). Truran quotes blast pressure as pounds to the square inch above the atmosphere and does not say at what pressure his air volumes are measured; treat the volumes as delivered volumes at the engine.
0. What the books give and do not give
- Truran gives air per minute for named furnaces (Dowlais, Hirwain, Dandyvan, Staffordshire, anthracite, Scotch, Langloan, Gartsherrie), air per cubic yard of capacity and per ton of iron, and a full table of the Dowlais blowing engines (cylinders, strokes, strokes a minute, air, coal, horsepower). It is the best source so far for sections 1 and 2.
- Truran gives no pig weight and no pig or sow dimensions. The refinery's casting bed and the blast furnace's tapping and cast sizes are given (section 4); the sand bed of the blast furnace is only called "the dust-bed". No book read gives the weight of a blast-furnace pig; the nearest figures are the puddler's charge pieces of 30-40 lb and Kirk's four foundry pieces to the hundredweight (section 4).
- Truran gives no receiver volume. The only figures are the blast main's area against the piston's and the abandoned hydrostatic regulator's air chamber (section 2).
- Truran gives no air per tuyere. The nozzle count and bore are given for some furnaces; the per-tuyere air is worked out here (INFERRED).
- No charcoal furnace of about 33 ft is described. Truran's charcoal furnaces are a paragraph (hearth, largest diameter).
- Johnson 1917 is about 500-ton American furnaces and turbo or gas blowing engines; it gives no puddling, no pig weight and no small-engine sizes. Its use here is the cross-check in sections 1, 3 and 4.
1. Furnace sizes against blast
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Capacity against diameter | 13 ft 3 in at the boshes, 44 ft high: about 140 cubic yards; 18 ft diameter, same height: 280 cubic yards | 107 m3; 214 m3 | 82 | "a furnace, 13 feet 3 inches diameter at the boshes, and 44 feet high in the interior, will contain about 140 cubic yards; and a furnace 18 feet diameter, and of the same height, 280 cubic yards" |
| Furnace diameters by district | Staffordshire 10-14 ft, Scotland 12-16, Welsh anthracite 10-14, South Wales 13-18 ft 6 in | 3.0-5.6 m | 131 | "The furnaces of Staffordshire are usually 10 to 14 feet diameter ; those of Scotland, 12 to 16 feet ; the Welsh anthracite furnaces are from 10 to 14 feet" |
| Furnace height | 40 and 45 ft, "nearly uniform" | 12.2-13.7 m | 113, 115 | "Since the height of the blast furnace has been increased to 40 and 45 feet, a blast of 2 3/4 to 3 lbs. to the square inch has become general" (the fraction reads "2 |
| Charcoal furnace | hearth about 2 ft square, largest diameter rarely over 9 ft | 0.6 m; 2.7 m | 126 | "In the charcoal furnaces the hearths are usually about 2 feet square, but the largest diameter of these furnaces rarely exceeds 9 feet." |
| Hearth width, coke or coal | 6 ft enough for coke; 7 ft with coal; Dowlais 8 ft; Aberamman 5 ft | 1.8-2.4 m | 126 | "Where coke is used as the fuel we are of opinion that 6 feet is wide enough for all purposes, but in full size furnaces, 16 to 18 feet in diameter across the boshes" |
| Dowlais foundry-iron furnace | 275 cubic yards, 5390 cu ft a minute, up to 130 tons a week, 20 cu ft a minute per cubic yard | 210 m3; 153 m3/min | 83-84 | "The foundry iron furnace at the Dowlais works is of 275 cubic yards capacity, and is blown with a blast of 5390 cubic feet of air per minute." "The consumption of blast per minute is at the rate of 20 cubic feet of air to each yard capacity of furnace." |
| Dowlais, weekly air | 50,550,400 cu ft, 1695 tons | 1431 thousand m3 | 83 | "The air delivered by the tuyeres weekly weighs 1695 tons and measures 50,550,400 cubic feet" |
| Dowlais, air per ton of iron | text reads 3,888,490 cu ft | - | 84 | "The ton of iron is produced with a consumption of 3,888,490 cubic feet of air." INFERRED: 50,550,400 / 130 t = 388,850, so the printed figure is ten times too large (a dropped point or a misprint); 13 tons of air a ton of iron agrees with 388,850 cu ft |
| Dowlais forge-iron furnace | same capacity, 7370 cu ft a minute, 170 tons iron and 310 tons cinder a week | 209 m3/min | 84 | "The blast averages 7370 cubic feet per minute." |
| Hirwain foundry-iron furnace | about 200 cubic yards, 2541 cu ft a minute, 90 tons a week, coke fuel | 153 m3; 72 m3/min | 85 | "The Hirwain foundry iron furnace measures 200 cubic yards in capacity nearly, and is blown with 2541 cubic feet of air per minute." |
| Dandyvan (Scotch carbonaceous ore) | 167 cubic yards, 3040 cu ft a minute, 150 tons a week, 18 cu ft a minute per yard | 128 m3; 86 m3/min | 86 | "The furnaces at the Dandyvan works average 167 cubic yards capacity. Blast 3040 cubic feet per minute." "The consumption of blast per minute is at the rate of 18 cubic feet per yard capacity." |
| Three furnaces compared | Dowlais 275 yd3, 6540 cu ft a minute, 24 per yard; Staffordshire 162 yd3, 4100, 25; anthracite 112 yd3, 4000, 36 | 185, 116, 113 m3/min | 76, 78 | "Into the Dowlais furnace is blown 6540 cubic feet of atmospheric air per minute, or 24 feet for each yard capacity into the Staffordshire furnace, 4100 feet per minute, or 25 cubic feet per yard; into the Anthracite furnace, 4000 cubic feet" |
| Make of the three | Dowlais 90 tons a week (6 cwt a yard), Staffordshire 65 tons (8 cwt), anthracite 50 tons (9 cwt) | - | 77, 80 | "the Staffordshire 65 tons of metal, or 8 cwts. nearly to each yard capacity" |
| Air per ton of pig, the three | Dowlais 732,386 cu ft (25 tons of air), Staffordshire 635,800 (22 tons), anthracite 806,400 | 20.7, 18.0, 22.8 thousand m3 | 78 | "Dowlais furnace, 732,386 cubic feet, weighing 25 tons; Staffordshire furnace, 635,800 cubic feet, weighing 22 tons nearly" |
| Air wanted by the 275 yd3 furnace | 8720 cu ft a minute, against the 6540 supplied; 8720 is also the figure for a full-power 18 ft furnace | 247 m3/min | 81, 134 | "Instead of 6540 cubic feet per minute, there should be 8720." |
| Small furnaces, big blast | 139 yd3 furnaces blown 47 cu ft a minute per yard, giving 15 1/2 cwt a yard; the 275 yd3 furnaces 24 a yard | - | 82 | "the blast, which amounts to 47 cubic feet per minute per yard capacity of furnace, against 24 feet per yard in the large furnace" |
| Blast reaching a furnace, by works | Dowlais four new furnaces, 21,560 cu ft a minute together; fourteen older, 77,000; Langloan six furnaces 14,824 (150 tons each a week); Gartsherrie eight furnaces on one engine, 24,335 | 610, 2180, 420, 689 m3/min | 161 | "At the Gartsherrie works, Scotland, eight of the furnaces are blown by a single engine, which delivers 24,335 cubic feet of air per minute." |
| Air per pound of carbon | Clyde cold blast 85 cu ft, hot blast 67; Dowlais 90 and 81; Hirwain 68; Langloan 44 | - | 161 | "This supply of air was at the rate of 85 cubic feet to each pound of carbon." |
| Air per pound of coke, 1917 | theory about 63 cu ft; actual 51; a turbo-blower test 41 | - | Johnson 164-165 | "about 63 ft. are required theoretically for this purpose without any loss by leakage" |
| Blast pressure, general | 2 lb minimum; 2 1/2-3 lb general; 4-5 lb for hard coal | 13.8; 17-21; 28-34 kPa | 113, 115 | "In the present state of the manufacture 2 lbs. to the square inch is a minimum degree of compression." "a pressure of 4 to 5 lbs to the square inch may be advantageously adopted" |
| Blast pressure against hearth width | 3 ft hearth 1 1/2 lb; 6 ft hearth 3 lb | 10; 21 kPa | 116 | "If to penetrate 3 feet requires a mean pressure of 1 1/2 lbs." (fraction reads "1-J" in the OCR) "of 6 feet the pressure would be 3 lbs." |
| Pressure at the nozzle | the discharge pipes drop it; the engine's 2 1/2-3 lb is more than 2 lb only at the engine | - | 116 | "but the diameter of the discharging pipes is such that at their termination a greater pressure than 2 lbs." (sentence cut off in the OCR) |
| Tuyere count, usual | three: one each side and one at the back; 10 and even 12 nozzles seen | - | 118 | "The most usual method is by three tuyeres, one on each side and the third at the back" |
| Tuyere count, by district | Swansea Valley 10 (three each side and back, one in the breast); Langloan 4; Dandyvan 5; Gartsherrie 4, 5 or 6; Monkland 5; Govan 8; Dowlais tried 6 for 3 | - | 120 | "In the Swansea Valley the furnaces are generally blown with 10 tuyeres, three each side and back, and one in the breast" |
| Small tuyeres tried at Dowlais | six for three: coal 45.3 cwt to 50.1 cwt a ton, weekly make 93 tons 15 cwt to 92 tons | - | 120 | "A loss consequently occurred from the small tuyeres of 4.8 cwts. of coal on each ton of iron" |
| Tuyere bore, blowing-in | a 275 yd3 furnace to be blown with 4 in nozzles starts on 1 1/2 in, then 2 1/4, 2 1/2, 3 1/2, 3 3/4 over four to five weeks | 38 mm, up to 102 mm | 41 | "For a furnace of an interior capacity of 275 cubic yards, and intended to be blown with 4-inch nozzles, the first set will be 1 1/2-inch bore." (fractions are damaged in the OCR; read as the sequence) |
| Nose-pipe taper | large end one-fourth bigger per foot of length; a 4 in nose 18 in long ends 5 1/2 in | 102 mm, 457 mm | 122 | "the large end should be one-fourth greater than the small for each foot in length" |
| Cold-blast feed pipe | wrought pipe 10 in, 6 ft long, telescoping, small end 5 in, large 8 in; elbow 10 in bore; nozzle 2 ft long | 254 mm, 1.83 m | 29-30 | "generally 10 inches in diameter and 6 feet long" |
| Damplate | 6 ft long, 3 ft high, 3 in thick; tapping opening 9 in wide by 20 in high; cinder notch 8 in wide, 24 in above the hearth bottom | 1.83 x 0.91 m | 28 | "This plate measures about 6 feet long, 3 feet high, and 3 inches thick." |
INFERRED, from the rows above:
- Air per tuyere: Dowlais 6540 cu ft a minute through three tuyeres is about 2180 each (62 m3/min); six small tuyeres on the same blast about 1090 each. Langloan 14,824 for six furnaces is about 2470 a furnace.
- Air per ton of iron a day: Dowlais foundry 5390 / (130 t / 7 d) = 290 cu ft a minute for each ton a day; Hirwain 2541 / (90 / 7) = 198; Johnson's three 40,000 cu ft turbos for two 500-ton furnaces (p. 155) 80-120. The 1917 furnace is two to four times as lean in air as Truran's, which agrees with his own complaint that the 1850s blast was a third short.
- A 33 ft by 9 ft charcoal furnace, scaled on Truran's 140 yd3 for 13.25 ft by 44 ft (volume = 0.489 D^2 H), holds about 1300 cu ft (48 yd3, 37 m3). At Truran's 18-47 cu ft a minute per cubic yard that is 870-2270 cu ft a minute (25-64 m3/min), about 1160 at his common 24.
2. Blowing engines
Date, engine builder and maker are Dowlais's. "Strokes" are double strokes unless noted; Truran's engines are double-acting.
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Engines in the country | about 310 | - | 182 | "There are in this country about three hundred and ten" |
| Old condensing engine | low-pressure, air pump, cold-water pump, a nozzle of five or six valves; steam 3-4 lb above atmosphere, mean 13 lb on the piston, 10 lb effective | 21-28 kPa | 183-184 | "The total mean working pressure on the steam-piston averages about 13 lbs. to the inch, but after deducting friction and leakage the effective pressure rarely exceeded 10 lbs." |
| Blowing cylinder to steam cylinder | area four times, giving a blast of 2 1/2 lb at most | 17 kPa | 184 | "the area of the blowing cylinder was made four times that of the steam cylinder. With these proportions the density could never exceed 2 1/2 lbs." |
| Piston speed, old and new | 180-200 ft a minute early; 260-300, some 400; high-pressure 650 | 55-61, 79-91, 122, 198 m/min | 184 | "The early double-acting blowing-engines were constructed to work at a velocity of 180 to 200 feet per minute." "a velocity of 650 feet per minute" |
| High-pressure engine | non-condensing, heavy fly-wheel, blast 8-10 lb possible; about a quarter cheaper than a condensing engine; speed average 400 ft a minute | 55-69 kPa | 183-185 | "High-pressure engines, having cylinders similarly proportioned to those of condensing engines, are capable of compressing the blast to a pressure of 8 to 10 lbs. to the square inch" |
| Beam against horizontal | vertical beam engines kept; horizontal ones "more inefficient and expensive in maintenance"; the horizontal piston wears fast | - | 185-186 | "we do not consider it possible in the present state of mechanical science to construct horizontal blowing-engines, that can successfully compete with those with vertical cylinders" |
| Blowing piston rod | sectional area at least double the steam rod's | - | 186 | "The smallest sectional area of the blowing piston-rod should be double that of the steam piston-rod" |
| Wind (inlet) valves | aggregate area at each end one-half the piston's area, silent at 600 ft a minute | - | 187 | "the wind valves work silently at a speed of 600 feet per minute, when the aggregate area at each end is one-half the area of the piston" |
| Delivery valves | aggregate area at each end not under one-seventh the piston's; one size throughout; two thicknesses of leather riveted, bars leaving about 6 in between beats | 150 mm | 187 | "The aggregate area of the delivery valves at each end ought to be not less than one-seventh the area of the piston." |
| Blast pipe | area at least one-seventh the piston's, one-fifth better, "acting as a magazine"; 24-60 in main in the Dowlais table | 0.6-1.5 m | 187 | "The area of the blast pipes should be as large as possible, as a rule not less than one-seventh of the area of the piston, a proportion of one-fifth even would be better, and by acting as a magazine would ensure greater regularity in the delivery of the blast" |
| Piston packing | hemp and oakum under a segmented junk ring; examined every 4-5 months, renewed every 16-18 months | - | 187 | "The piston goes four or five months without calling for examination, and the packing is renewed once only in sixteen or eighteen months." |
| Steam stroke longer than blast stroke | the beam is made so the steam cylinder's stroke is longer, so steam works expansively | - | 187 | "we find the working of the engine improved when the stroke in the steam cylinder is longer than in the blowing cylinder" |
| Strength and running | every part twice as strong as other engines; should run a month, then one hour's delay; about 30 hours stopped a year | - | 183, 188 | "every part of a blowing-engine should be twice as strong as in any other class of engine" |
| Hydrostatic regulator | an air chamber over a water seal, chamber area about twice the blowing cylinder's; common "some years ago"; given up because the blast carried water into the furnace | - | 111 | "the sectional area of the air-chamber in the hydrostatic regulator was about twice the area of that of the blowing cylinder" |
| Receiver volume | not given | - | - | not documented in Truran |
Dowlais blowing engines (Truran's table, pp. 189-191)
Read from the page images; the digits were checked against the swept volumes below. Rows are in the table's order.
| Row | Built | Type | Blowing cyl dia | Steam cyl dia | Stroke | Strokes a min | Air a min, at lb | Coal a day | cu ft per lb coal |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 1790 | condensing | 87 1/8 in (2.21 m) | 41 in | 7 ft 6 in (2.29 m) | 19 | 11,970 cu ft (339 m3), 2 1/4 | 8.0 t | 800 |
| 2 | 1800 | condensing | 108 in | 50 in | 7 ft 6 in | 18 | 17,226 cu ft (488 m3), 2 1/4 | 11.5 t | 797 |
| 3 | 1817 | condensing | 100 in | 50 in | 7 ft 6 in | 20 | 16,350 cu ft (463 m3), 2 1/4 | 11.5 t | 681 |
| 4 | 1824 | condensing | 108 in (2.74 m) | 54 1/4 in | 7 ft 6 in | 17 | 16,218 cu ft (459 m3), 2 1/4 | 11.0 t | 790 |
| 5 | 1828 | high-pressure | 144 3/4 in (3.68 m) | 54 in | 9 ft 3 in (2.82 m) | 13 | 27,476 cu ft (778 m3), 2 1/4 | 15.0 t | 980 |
| 6 | 1836 | high-pressure | 122 in | 40 in | 8 ft 0 in | 16 | 20,687 cu ft (586 m3), 2 1/4 | 13.0 t | 850 |
| 7 | 1839 | high-pressure | 144 in | 53 in | 9 ft 0 in | 14 | 28,476 cu ft (806 m3), 2 3/4 | 17.0 t | 998 |
| 1850 | 1850 | high-pressure | 144 in (3.66 m) | 55 in (1.40 m) | 12 ft 0 in (3.66 m) | 19 | 51,528 cu ft (1459 m3), 3 | 25.0 t | 1328 |
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Biggest engine in the text | blowing cylinder 144 in, stroke 12 ft, 19 double strokes a minute, 51,528 cu ft a minute at 3 lb, coal 25 tons a day | 3.66 m; 1459 m3/min; 20.7 kPa | 188 | "No. 1 blowing-engine, high-pressure, non-condensing: blowing cylinder, 144 inches in diameter; stroke of piston, 12 feet; 19 double-strokes per minute; quantity of air at a pressure of 3 lbs. to the square inch discharged per minute, 51,528 cubic feet." |
| No. 5, high-pressure | 144 in, 9 ft 3 in, 13 a minute, 27,476 cu ft at 2 1/4 lb, 15 tons coal a day | - | 188 | "stroke, 9 feet 3 inches; strokes per minute, 13; quantity of air per minute at a pressure of 2 1/4 lbs., 27,476 cubic feet" |
| No. 4, low-pressure condensing | 108 in, 7 ft 6 in, 17 a minute, 16,218 cu ft at 2 lb, coal 11 tons | 2.74 m | 188 | "blowing cylinder, 108 inches in diameter; stroke, 7 feet 6 inches; strokes per minute, 17; quantity of air at a pressure of 2 lbs. per minute, 16,218 cubic feet" |
| Hirwain, condensing | 104 in, 7 ft 3 in, 16 a minute, 13,688 cu ft at 3 lb, coal 17.2 tons | 2.64 m | 188 | "Blowing-engine, low-pressure, condensing: blowing cylinder, 104 inches in diameter; stroke, 7 feet 3 inches; strokes per minute, 16" |
| Gartsherrie, condensing | 120 in, 9 ft 6 in, 16 a minute, 24,335 cu ft at 2 3/4 lb, coal 35 tons | 3.05 m | 188-189 | "blowing cylinder, 120 inches; stroke, 9 feet 6 inches; strokes per minute, 16" |
| Monkland, horizontal | 72 1/2 in, 9 ft, 18 a minute, 9298 cu ft at 3 lb, coal 15 tons | 1.84 m; 263 m3/min | 189 | "blowing cylinder, 72 1/2 inches in diameter; stroke, 9 feet; strokes per minute, 18; quantity of air per minute at a pressure of 3 lbs., 9298 cubic feet" (the fraction is damaged in the OCR) |
| Wingerworth, pair, horizontal | two cylinders 48 in, 7 ft, 12 a minute, 4221 cu ft at 2 1/4 lb together, coal 6.5 tons a day | 1.22 m; 120 m3/min | 189 | "Pair of blowing-engines, high-pressure, horizontal cylinders: blowing cylinders, 48 inches diameter; stroke, 7 feet; strokes per minute, 12; quantity of air per minute at a pressure of 2 1/4 lbs., 4221 cubic feet" |
| Fan engine, Wingerworth | direct-acting revolving engine working fans, 4200 cu ft at 1 1/2 lb, coal 8.6 tons a day | 10 kPa | 189 | "quantity of blast generated at a pressure of 1 1/2 lbs. to the square inch, 4200 cubic feet per minute" |
| Duty, three classes | high-pressure beam 1154 cu ft of 3 lb blast per pound of coal; condensing 560; horizontal 356; fan 166 | - | 189 | "the mean duty of the high-pressure engines is 1154 cubic feet; of the low-pressure condensing-engines, 560 cubic feet; and of the high-pressure horizontal, 356 cubic feet" |
| Steam cylinder, mean pressure, power | engine 1850: 55 in steam cylinder, 696 hp on the steam piston, 600 hp given out by the blast piston, 86 per cent; whole set: 2356 hp on steam, 2036 hp on blast, 86.4 per cent | 519, 447 kW | 190 | "Total ... 2356 ... 2036 ... 86.4" |
| Mean blast pressure on the piston | 2.15-2.66 lb a square inch across the eight engines | 15-18 kPa | 190 | table column "Mean pressure of the air on the blowing piston" |
| Engine size | "averaging as they do more than 250-horse-power each" | 186 kW | 190 | "The large size of these engines - averaging as they do more than 250-horse-power each" |
| Fly-wheel | engine 5: 15 ft; 6: 16 ft; 7: 22 ft 6 in; 1850: 20 ft | 4.6, 4.9, 6.9, 6.1 m | 191 | table column "Diameter of fly-wheel" |
| Beam | 1850 engine: 12 ft stroke, main beam gudgeons 13 1/2 in, beam 6 ft 6 in deep at the middle, plates 3 1/2 in; blast main 60 in; wind valves 56 sq ft | - | 191 | table columns |
| Boilers for the 1850 engine | six boilers, 7 ft by 42 ft, tubular, 55 lb steam, 4092 sq ft heating surface | 2.13 x 12.8 m; 380 m2 | 191 | table, continued |
Checks (INFERRED). Swept volume = piston area x stroke x 2 x strokes a minute:
- 1850 engine: 144 in is 113.1 sq ft; 113.1 x 12 x 2 x 19 = 51,570 cu ft, against 51,528 printed.
- No. 4: 108 in is 63.6 sq ft; 63.6 x 7.5 x 2 x 17 = 16,222, against 16,218.
- Monkland: 72.5 in is 28.7 sq ft; 28.7 x 9 x 2 x 18 = 9289, against 9298.
- Wingerworth pair: 48 in is 12.57 sq ft; 12.57 x 7 x 2 x 12 x 2 = 4224, against 4221.
So the printed delivery is the swept volume with no leakage deducted; "air delivered" and "displaced" can be one number in a model. A single Wingerworth cylinder is 2110 cu ft a minute (59.8 m3/min).
Power against air (INFERRED): hp on the blast piston = mean pressure (lb/sq in) x 144 x cu ft a minute / 33,000. For the 1850 engine 2.66 x 144 x 51,528 / 33,000 = 598 hp, Truran's 600. So about 0.0116 hp for each cu ft a minute at 2.66 lb mean, and the steam piston supplies about 14 per cent more (friction and inertia: 86 per cent given out). A Wingerworth cylinder at 2 1/4 lb mean on 2110 cu ft is about 2.25 x 144 x 2110 / 33,000 = 21 hp on the blast piston, 24 hp on the steam piston. Overman's tub machine (12-16 hp for a charcoal furnace) sits below it, as it should at 5/8 lb.
Johnson 1917 (blowing-engine cross-check, 1917): a vertical quarter-crank engine, 42 in steam and 84 in air by 60 in stroke, p. 142; a horizontal-vertical cross-compound, 52 and 90 in steam, 90 in air by 60 in stroke, p. 143; "speeds at which they are required to run" 40 revolutions rated for steam, "from 70 to 85 revolutions" for gas engines, "42 and 80 x 60 gas engine with a rated speed of 65 revolutions", p. 183; three turbo blowers, "40,000 cu. ft. per minute each to a pressure of 30 lb", p. 155. One 84 in by 60 in steam-driven engine at 40 revolutions is 38.5 sq ft x 5 ft x 2 x 40 = 15,400 cu ft a minute (INFERRED), the size of Truran's Dowlais No. 4, so a 1917 engine is what Truran's biggest was.
3. Hot-blast stoves
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Layout | two horizontal cast pipes 14 in bore, 18 in outside, 26 sockets each, vertical horseshoe pipes standing in them, the blast taken through in passes; chimney 8-9 ft above the roof with a damper | 356 mm, 457 mm | 37-38 | "The horizontal pipes are 14 inches internal, and 18 inches external diameter. Each pipe has on its upper side 26 sockets, 6 inches deep and 8 1/2 inches between centres." |
| Horseshoe pipe | 8 ft 3 1/2 in over foot and crown, 5 ft over the legs, V-shaped bore 18 sq in | 2.52 m, 1.52 m | 38 | "measure over the foot and crown 8 feet 3 1/2 inches, and over the legs 5 feet" (fractions damaged in the OCR) |
| Fireplaces | two to each stove, each 2 ft 3 in wide by 6 ft 11 in long | 0.69 x 2.11 m | 38 | "The fireplaces, two to each stove, measure 2 feet 3 inches wide by 6 feet 11 inches long." |
| Heating surface of one stove | 1001 sq ft; 2020 cu ft a minute at 3 lb; 600 degrees F | 93 m2; 57 m3/min | 38-39 | "The quantity of blast passing through the inlet pipe of each stove, at an average pressure of three pounds to the square inch, is 2020 cubic feet per minute." |
| Rule of the large stove | 500 sq ft of heating surface and 15 1/2 sq ft of grate for each 1000 cu ft a minute, to 600 degrees F | 46 m2 | 39 | "for each 1000 cubic feet of blast heated to a temperature of 600 deg." |
| Rule of the small stove | 270 sq ft and 8 sq ft of grate for each 1000 cu ft a minute, "the minimum" | - | 39 | "270 square feet of heating surface, and 8 square feet of grate surface, or a little more than one-half of the proportional areas in the other stove" |
| Expansion | 1000 volumes of cold blast become 2050 at the stove's temperature | - | 38 | "its volume be equal to 1000 at entering the stove, it will have expanded to 2050" (the page before p. 39; temperature in the cut sentence) |
| One stove to one tuyere | the Dowlais plan; "a single stove placed at the back" in crowded old works | - | 37 | "to erect a separate stove to each tuyere" |
| Johnson 1917 stove size | stove diameter about the bosh diameter, height the furnace's up to 20-25 per cent more; not under 4 and better 5 sq ft of heating surface per cu ft of blast a minute | - | Johnson 228-229 | "not less than four and preferably five square feet of heating surface per cubic foot of blast blown per minute measured by piston displacement" |
INFERRED: Truran's large stove 500 sq ft per 1000 cu ft a minute is 0.5 sq ft per cu ft, a tenth of Johnson's 5; the old pipe stove ran at 600 degrees F, the 1917 firebrick stove far hotter.
4. Pigs, the sow and the beds
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Weight of a blast-furnace pig | not given | - | - | not documented in Truran or Johnson 1917 |
| Charge for a puddling furnace, pieces | the pigs are broken to 30-40 lb | 13.6-18.1 kg | 208 | "is charged in pieces of convenient size - 30 to 40 lbs. is best, and the more uniform the better" |
| Foundry pigs broken | four pieces to the hundredweight | 25-28 lb, 11-13 kg (INFERRED, cwt of 100 or 112 lb) | Kirk, PDF 267 | "and pig was weighed by counting the pieces, estimating four pieces to the hundred weight" |
| Cast, in a new furnace | first 3-3 1/2 tons collect in 60 hours; second cast about 2 tons; each cast about 5 tons by the fourth week | 3.0-3.6 t; 2.0 t; 5.1 t | 41 | "will collect in the hearth to the amount of 3 or 3 1/2 tons in sixty hours after blowing-in" "to about 5 tons each cast in the fourth week" |
| Blast furnace casting | tapped through a cast-iron trough about 6 ft long from the tapping hole to the casting bed or refinery | 1.83 m | 29 | "a cast-iron trough, about 6 feet long, to convey the fluid metal from the tapping-hole to the casting-bed or refinery" |
| Casting times | cast at stated periods; Overman: "Six in the morning, and six in the evening" | - | Overman 201 | "Six in the morning, and six in the evening is the time usually set apart for casting." |
| Pig-bed work | the keeper (helper at large furnaces) prepares the pig bed and moulds the pigs; after the cast the pigs are removed, weighed, stored and the bed's sand dug up, wetted and prepared | - | Overman 201, 206 | "The preparation of the pig bed, moulding of pigs, is the duty of the keeper" |
| Pig moulds of cast iron | the refinery's mould blocks are grooved "very similar to those of the moulds prepared in the dust-bed of the blast-furnace for forming the original pigs"; the size is not stated | - | 194 | "the dimensions and length being very similar to those of the moulds prepared in the dust-bed of the blast-furnace for forming the original pigs" |
| Refinery casting bed | cistern about 30 ft long, 4 ft wide, 2 ft deep; cast-iron blocks 3 1/2 ft wide and long, 6 or 8 in thick, sloping flanges, a flange down the middle; water to within an inch or two of the blocks | 9.1 x 1.2 x 0.6 m; 1.07 m, 150-200 mm | 193 | "A brick, or, what is better, a cast-iron cistern, about 30 feet long, 4 feet wide, and 2 feet deep, forms the substructure." |
| Refinery charge | about 2 tons of pig, 5 cwt coke; three hours a fireful; tapped plate broken for the puddler | 2.03 t, 254 kg | 194-195 | "The weight of pig-iron or other metal charged will vary with the size of the fire, but may be taken at 2 tons, and the coke for the same at 5 cwts." |
| Johnson, sow and pig | "a sow with a litter of suckling pigs"; the main runner is the sow, branch runners then pigs at right angles to it, together a "bed" | - | Johnson 328 | "The combination of the branch runner or sow and the pigs which go with it are known as a 'bed.'" |
| Johnson, sand | coarse, open-grained, free of clay, lime and iron oxide to prevent a boil; cast beds of sand until about 1897 | - | Johnson 328-329 | "It must be coarse and open-grained, practically free from clay to prevent boils" |
| Johnson, chill bed | cast iron, 9-12 in thick including the "cores" between pigs, 6-8 in under a pig; over 4 ft across the length of the pig, 18-20 ft long, weighing many tons, cast in two or three pieces | 230-300 mm; 150-200 mm; over 1.2 m; 5.5-6.1 m | Johnson 330 | "The width of the chill in the direction of the length of the pig is over four feet and its length may be anything dictated by the size of the cast house and local conditions, but beds eighteen or twenty feet long are not uncommon." |
| Johnson, breaking | a pig breaks from the sow by a bar under the joint, hot or cold; the old pig broken in two; Duquesne pigs "vastly larger, both of heavier cross section and much longer" | - | Johnson 331-333 | "the individual pigs were made vastly larger, both of heavier cross section and much longer than the ordinary pig" |
| Johnson, pig machine | casting machines, chilled moulds on a moving chain, replace the sand bed; the sand bed "will for years to come" persist at merchant furnaces | - | Johnson 332 | "many merchant furnaces supplying the foundry trade still continue to cast their iron in sand" |
Secondary leads, from a web search snippet only and not read: museum records of 18th-century pigs (https://emuseum.colonialwilliamsburg.org/objects/86980/occoquan-furnace-iron-pig, a pig 30 1/2 x 5 x 5 in; a Fredericksville pig 36 x 8 in), a Penn State note that pigs weighed "well over 50 pounds" (https://engr.psu.edu/mtah/essays/pigiron.htm), and a Dubuque local history of 1836 giving seventy pigs of seventy pounds each. None is an ironmaking-book source; they are leads for a primary check.
INFERRED:
- Truran's charge pieces of 30-40 lb (13.6-18.1 kg) and Kirk's 25-28 lb pieces (11-13 kg) are pieces of a pig; a whole pig is larger, which Kirk's "pig broken in two" and the museum figures (50-70 lb, 23-32 kg) fit.
- Pigs a cast: a cast of 5 tons is 5080 kg, so about 160-220 pigs of 23-32 kg; a 2-ton cast is 2030 kg, about 63-88 pigs.
- Johnson's chill bed gives the pig's length: it is under 4 ft (1.2 m), as the chill is "over four feet" across the length of the pig, and a bed is a row of such pigs along an 18-20 ft sow.
5. Puddling furnace, charge and ball
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Boiling furnace frame | cast-iron plate frame about 12 ft long, 5 ft 6 in wide inside, 6 ft high; ash pit 2 ft deep | 3.66 x 1.68 x 1.83 m | 205 | "constructed with an outside framework of cast-iron plates, about 12 feet long, 5 feet 6 inches wide inside, and 6 feet high" |
| Grate | 8-12 sq ft; 3 ft 9 in wide at the fire end, narrowing to 16-18 in at the stack | 0.7-1.1 m2 | 205 | "the superficial area of the grate shall be from 8 to 12 feet" |
| Hearth body | about 6 ft long, 3 ft 9 in wide, 2 ft high to the roof's centre; roof arch 27 in at the fire | 1.83 x 1.14 x 0.61 m | 205-206 | "When finished the body of the furnace measures about 6 feet long, 3 feet 9 inches wide, by 2 feet high to the centre of the roof." |
| Bridges | fire bridge 14-15 in thick and rising to within 10-12 in of the roof; flue bridge 9 in thick, 10-12 in high (puddling furnace: 6 in) | - | 206, 210 | "a brick bridge, 14 or 15 inches thick, is built on the extreme end of the bottom plate" |
| Doors | working door about 16 in square; charging door about 10 by 13 in, 12-13 in above the plate, both lifted by lever and balance weight; slit 3 1/2 by 5 in in the working door | - | 206 | "a small slit, about 3 1/2 inches wide by 5 inches high, is left in the under side of the door" |
| Stack | 30 ft above the frame, 36 ft in all; flue about 24 in square, throttled to a third at the roof | 9.1 m, 11 m | 207 | "For the generality of forge coals it is 30 feet high above the cast-iron framework, or altogether 36 feet." |
| The heat (charge) | 4 1/4 or 4 1/2 cwt of pig | 216-229 kg | 208 | "the quantity of pigs to be operated on - technically called a 'heat' - generally 4 1/4 or 4 1/2 cwts." |
| Pieces | 30-40 lb | 13.6-18.1 kg | 208 | "30 to 40 lbs. is best" |
| Cinder added | 30-40 lb of cinder first, 60-80 lb a quarter hour after charging, 15 lb at the bridge | 14-18, 27-36, 7 kg | 208 | "In about a quarter of an hour after charging the puddler throws in about 60 or 80 lbs. of the cinder expelled by the rolls" |
| Steps and times | edges melt 22-25 min after charging; all melted in 30 min; boil 18 min; balling 8-9 min; drawing balls 4 min; total 1 h 20 min (good men) to 1 h 50 min | - | 208-209 | "From charging the first piece of pig to the extraction of the last ball the time occupied will average, with good workmen and a fair coal, one hour and twenty minutes" |
| Balls to a heat | five or six usual, seven or eight seen | - | 209 | "The number of these depends on the iron charged and the ability of the workman. Five or six is usual, but seven or eight may be seen brought out." |
| Heats a turn | eight in twelve hours, 32 cwt of bars a shift, 9 tons 8 cwt a week a shift, 18 tons 16 cwt night and day | 1.6 t a shift; 19 t | 209 | "a puddler and his second hand will easily boil eight heats in the twelve hours" |
| Make | single furnace 18 tons a week (Staffordshire 10); double furnace 36 tons, 46 working on hot metal | - | 216-217 | "The make of the double boiling furnace averages 36 tons weekly." |
| Yield | 21 cwt 20 lb of forge pig a ton of puddled bars on average of 85 furnaces over 22 years; 20 cwt best case | 21.7 cwt = 1.1 t of pig | 215 | "taking the average of eighty-five furnaces over twenty-two years, we find the yield to average 21 cwts. 20 lbs." (the page's figure wording is cut in the OCR) |
| Coal | 14 cwt a ton of bars with a flaming coal, 18 with a poorer, 22 near anthracite | - | 215 | "With a bituminous coal yielding much flame the consumption with superior workmen will average 14 cwts." |
| Puddling (not boiling) | general charge about the same, 4 1/2 cwt; flue bridge about 6 in; bottom within 8 in of the door | - | 210 | "The general charge is 4 1/2 cwts." (fraction damaged in the OCR) |
| Ball weight | not stated | - | - | not documented |
| Ball to bloom | the shingler reduces the ball under the hammer or squeezer to a bloom about 5 in diameter by 18 in long, 15-20 squeezer strokes | 127 x 457 mm | 219 | "it is reduced to a bloom about 5 inches in diameter by 18 inches long" |
| Refinery | about 4 ft square inside, 15-18 in deep; two or three nozzle pipes each side, nozzles 1 1/2 in; blast at 38 degrees, the two streams 105 degrees apart | 1.22 m, 38 mm | 193-196 | "The nozzles of the blowing pipes, in double refineries, where four are employed, are usually 1 1/2 inch diameter" (fraction damaged in the OCR) |
INFERRED: eight heats of 4 1/4 cwt are 34 cwt of pig for 32 cwt of bars a shift, 94 per cent (the bars lose the cinder, the pig yield above is 21.5 cwt for 20 cwt). A heat's bars are 32 / 8 = 4 cwt (203 kg), so with five or six balls a ball is about 34-41 kg (75-91 lb) of iron; the 5 in by 18 in bloom is 353 cubic inches, about 99 lb (45 kg) at 0.28 lb a cubic inch, which agrees with a ball of 90-100 lb squeezed to a bloom. A 4 1/4 cwt heat is 216 kg, 12-16 pieces at 13.6-18.1 kg.
6. Forge and mill hammers, squeezers, rolls
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Shingling hammer, bed | timber bedding 1000-1500 cu ft of oak under a cast-iron bed-plate about 24 ft by 7 ft, 10-12 tons | 28-42 m3; 7.3 x 2.1 m, 10-12 t | 218 | "capped by a cast-iron bed-plate measuring about 24 feet by 7 feet, and weighing from 10 to 12 tons" |
| Shingling hammer, helve | T-shaped, about 8 ft long by 6 ft wide at the centre of vibration, 2 ft deep by 12 in wide in the middle, 5-7 tons; hammer-face 18 in square | 2.4 x 1.8 m, 5.1-7.1 t; 457 mm | 218 | "The helve is T-shaped in plan, and measures about 8 feet long by 6 feet wide at the centre of vibration ... It weighs from 5 to 7 tons." |
| Anvil block | 5-6 tons, anvil-face like the hammer-face; face 16 cwt | 5.1-6.1 t | 218 | "the anvil-block, weighing from 5 to 6 tons" |
| Cam ring | 5 ft diameter, four wipers; 18-19 turns a minute; 72-76 blows a minute; lift about 16 in | 1.52 m; 0.41 m | 218-219 | "proportioned to 18 or 19 revolutions of the cam-ring; consequently, with 4 wipers in the cam, the number of blows ranges from 72 to 76 per minute" |
| Total castings of a medium hammer | 41 tons 10 cwt: bed 11 tons, standards 3 tons, helve 5 tons 10 cwt, hammer face 15 cwt, anvil block 5 tons 10 cwt, anvil face 16 cwt, shaft 2 tons 10 cwt, cam-ring shaft 7 tons, cam ring 4 tons 5 cwt, four wipers 24 cwt | 42.2 t | 218 | "Bed, 11 tons; helve standards, including brasses, 3 tons; helve, 5 tons 10 cwts.; hammer-face, 15 cwts.; anvil-block, 5 tons 10 cwts." |
| Blows to a ball | 15-25 blows in 18-30 s | - | 219 | "The puddle balls receive from 15 to 25 blows, occupying from 18 to 30 seconds, to convert them into blooms." |
| Double squeezer | bed 20 ft by 5 ft, 6 tons; anvil-faces 6 ft by 18 in; hammer-faces 3 ft by 18 in; crank stroke 16 in; castings 21 tons 13 cwt | 6.1 x 1.5 m; 22 t | 219 | "For a double-ended squeezer, the cast-iron bed-plate is laid on two longitudinal baulks of timber; it measures about 20 feet by 5 feet, and weighs 6 tons." |
| Squeezer speed | crank 45-80 turns a minute, 56-60 best; 25 s a ball, 25 blows | - | 219-220 | "The time occupied in squeezing each ball averages 25 seconds when the crank revolves 60 times per minute, giving 25 blows altogether to each bloom." |
| Puddling rolls | 18 in diameter by 3 ft 6 in between bearings, 6 ft 6 in over the necks; 35-80 turns a minute | 457 mm x 1.07 m | 224 | "The puddling rolls are generally 18 inches diameter by 3 feet 6 inches long between bearings" |
| Pile for the mill | 4 cwt pile; a heating furnace 36 piles in 12 hours, 83 tons a week; loss 80 lb a ton on large piles | 203 kg | 227 | "Piles of this size weigh about 4 cwts. At this rate, a heating furnace will work 36 piles in the twelve hours, or 83 tons of iron per week." |
| Mill hammer | in the contents at p. 231; not read in this pass | - | - | - |
7. Gaps
- The weight and size of a blast-furnace pig, the sow and the sand-bed layout. Truran, Johnson 1917, Overman 1851, Kirk and Bolland give none; the figures nearest are the 30-40 lb charge pieces and Kirk's four to the hundredweight. A primary source is open (Scrivenor, The Iron Trade of the United Kingdom, 1854; Percy 1864 on the casting bed; Truran's plates 216, 217, 243, 247 and 248 show the pig mould and are not digested).
- A receiver or regulator volume. Truran gives the blast main's area (a seventh or fifth of the piston's, "a magazine") and the abandoned water regulator's air chamber (twice the cylinder's area). Overman gives a receiver "very nearly" a cylinder's size, for a tub machine.
- Air per tuyere, per tuyere nozzle bore against furnace size: only the 4 in nozzle on a 275 yd3 furnace is given.
- A small charcoal furnace's blast and engine. Truran's smallest engine is the 48 in Wingerworth pair; Overman's tub machine is the charcoal figure.
- The Dowlais table is read from an image; a few digits (the second and third cu ft rows) are one in the last place uncertain, the swept-volume check agrees with rows 4, 1850, Monkland and Wingerworth only. The "area of blast main per square foot of piston" column is not used (it disagrees with the main's printed diameter).
- Truran's "pressure" for the table's air volumes and the blast's measuring point are not stated (section 0).
- A 3,888,490 against 388,850 cu ft of air a ton (section 1) is a misprint or an OCR loss; the page image was not checked.
- Mill hammer, forge hammer by name (p. 231 contents), the helve hammer's cam-ring drive power, and hammer mass against the work: only the shingling hammer was read.
- Hot-blast stove air against time and temperature: only the two Dowlais stove proportions and a 600 degrees F figure.