Percy, Rankine, Fairbairn, Courtney and Wilson on wrought iron grades against shear steel
Books Metallurgy: Iron and Steel, A Manual of the Steam Engine and Other Prime Movers, Iron, its History, Properties and Processes of Manufacture, The Boilermaker's Assistant, A Treatise on Steam Boilers
Covers the tensile strength of wrought iron by grade and brand against blister, shear and cast steel. Pages below are printed folios. A digest only. Read
- J. Percy, Metallurgy: Iron and Steel (1864), Kirkaldy's experiments, Tables IV to VIII (pp. 868-870, PDF page = folio + 26), viewed as images; shear steel (p. 859).
- W. J. M. Rankine, Manual of the Steam Engine, tenacity table (p. 67, PDF 97), viewed as an image; boiler plate (p. 68).
- W. Fairbairn, Iron, its History, Properties and Processes, steel (pp. 271-273, PDF 302-304).
- Courtney, Boiler Maker's Assistant (p. 92) and Wilson, Treatise on Steam Boilers (pp. 37, 73), as already digested in steam boilers, not re-read. Not readable as text Percy, Rankine, Fairbairn and Courtney have no text layer. Tables come out garbled, so every figure quoted here was read from the page image.
One series: Kirkaldy, in Percy
Percy prints Kirkaldy's means as "Abstract of Mean Results of Experiments on the Tensile Strength of Wrought-Iron Bars, Plates and Angle-Iron; Steel Bars and Plates. From Kirkaldy's Experiments" (p. 868). Breaking weight per square inch of original section, and contraction of area at fracture.
Table IV, round and square bars (p. 868):
| Districts and brands | Expts | lb | tons | Contraction % |
|---|---|---|---|---|
| Yorkshire, Low Moor, Bowling, Farnley | 20 | 61,644 | 27.5 | 49.8 |
| Lanarkshire, Govan, Extra B Best | 12 | 58,181 | 26.0 | 49.4 |
| Do., Best Best B Best, B Rivet | 61 | 58,737 | 26.2 | 36.0 |
| Do., Best | 24 | 58,265 | 26.0 | 22.6 |
| Staffordshire charcoal | 4 | 57,216 | 25.6 | 60.9 |
| Do., B B scrap | 4 | 59,370 | 26.5 | 52.0 |
| Do., B.C. Best Best | 21 | 58,698 | 26.2 | 39.5 |
| Do., Best K. B. M. | 4 | 55,000 | 24.6 | 27.0 |
| Lancashire Best Rivet | 8 | 53,775 | 24.0 | 48.6 |
Table VII, steel bars, F forged, R rolled (p. 870):
| Name | Expts | lb | tons | Contraction % | |
|---|---|---|---|---|---|
| Turton's cast-steel for tools | F | 6 | 132,909 | 59.3 | 4.7 |
| Jowitt's double shear-steel | F | 4 | 118,468 | 52.9 | 19.6 |
| Wilkinson's blister-steel | F | 4 | 104,298 | 46.6 | 21.4 |
| Jowitt's cast-steel for taps | F | 4 | 101,151 | 45.2 | 28.8 |
| Mersey Company's puddled steel | F | 6 | 71,486 | 31.9 | 35.3 |
Same-series ratios (inferred): Best Yorkshire bar to double shear steel 27.5 / 52.9 = 0.52; Lancashire Best Rivet to double shear steel 24.0 / 52.9 = 0.45; Lancashire Best Rivet to Best Yorkshire 24.0 / 27.5 = 0.87. Shear steel carries about half the contraction of best iron (19.6 against 36 to 50 %), tool cast steel a tenth.
Shear steel, p. 859: "Bars of blister-steel are broken into pieces about 16 in. long, and drawn out at a red heat under the hammer ... Several bars thus obtained are piled on one another ... welded under the hammer, and reduced to about 2 in. square. ... In this state it is termed 'single shear-steel.' It may be broken into two equal parts, which may again be welded together and drawn out to any required dimensions to form 'double shear-steel.'"
Other tables
Rankine, p. 67, tenacity in lb per square inch: "Iron, malleable: boiler plates, 51,000; bars, rods, and bolts, 60,000 to 70,000; wire, 70,000 to 100,000"; "Steel, 100,000 to 130,000". Bar iron to steel 0.46 to 0.70 (inferred). P. 68: "The tenacity of good wrought iron boiler plates has been stated as 51,000 lbs. per square inch."
Fairbairn, Iron, p. 272, lb per square inch: "Uchatius' cast-steel 90,000; Ordinary cast-steel 138,000; Krupp's steel gun 129,000; Mersey puddled steel 94,752 (Mallet); Sheffield cast-steel 130,000 (Rennie)". P. 272 also: the hammer or rolls "produced nearly double the strength" of Bessemer metal over its cast state.
Courtney p. 92: "Best Yorkshire plate, 25 tons"; "Crown, or best Staffordshire plate, 20 tons" (ratio 0.80). Wilson p. 37: Best Best plate 21 tons at 7 % elongation, the very best 24 tons at 12 % (ratio 0.875); p. 73: "Taking 21 tons per square inch as our standard strength for plates along the fibre".
No source gives
- A tested figure for the No. 1 puddle bar itself (it was not sold; Truran p. 227 names it as the pile stock).
- Hardness or edge-holding by iron grade.