Bolland, The Iron-Founder (1892)

Books The Iron-Founder

Covers S. Bolland, "The Iron-Founder: A Comprehensive Treatise on the Art of Moulding" (1892, 402 PDF pages). Pages below are the book's printed folios, which are the PDF page less fourteen. The contents list (pp. v-vii): cores Part II p. 121, elbows, bends and branch pipes in loam p. 209, large elbows on end p. 227, pulleys Part V p. 284, patterns from models p. 339; it adds the steam cylinder in dry sand (pp. 243-263), guns and hydraulic cylinders (p. 264), rolls in spindle flasks (p. 274), irregular pipes in green sand (p. 324) and pipes and columns by machine (p. 335). PDF pages 2, 4-6, 14, 384, 397-399 and 402 carry no text layer (front matter, a contents page, advertisements). Read: flasks, ovens, crystallization and shrinkage, pressures in moulds, chilled castings and roll mixtures (pp. 37-120), all of Parts II, IV and V, loam moulding, condensers and hot-wells, elbows and large elbows (pp. 147-232), patterns (pp. 339-349). Skimmed: kettles and casings (pp. 180-191), the screw propeller (pp. 203-209), bevel and spur wheels (pp. 305-324). Skipped: the essays and tools of Part I (pp. 1-36). The Part VI tables (pipe, column and plate weights, pp. 352-369) are images with no text layer and were not read. Figures looked at: the roll-mixture table (p. 120), the plain loam cylinder with its head (Fig. 128, p. 148) and the dry-sand steam-cylinder mould (Fig. 202, p. 245). Subject pig beds, sand and loam moulding, patterns, cast pipe, the pour, and which parts of a steam machine are cast and which are cast and then bored. Melting is Kirk's.

  • A flask is sized so the rammer works 2-3 in. from the pattern; a wooden one needs more sand against burning, so iron flasks are smaller (p. 37). Large flasks are built of loose sides and bars cast in open sand (p. 42).
  • The parting decides the finish: in a floor mould "smooth upper surfaces, and equally rough and unsightly lower surfaces" (p. 46), which is why critical work goes to dry sand or loam, or to hinged flasks that open every face to the moulder (pp. 46-52).
  • A steam cylinder is moulded in a three-part flask with the steam chest down and cast on end (pp. 243-246).
  • Many castings need no full pattern: loam is struck with spindle and sweep (pp. 148-170), pulleys are made from sweeps and cores (pp. 291-294), spur wheels from a segment and spindle (pp. 315-321), rails, lintels and column bases from a templet and strickle (pp. 340-344).

Pressure and lift in the mould (pp. 88-113)

  • Every part of a full mould bears the weight of a column of iron up to the top of the running basin, at 0.26 lb per cubic inch (p. 89). The lift on the cope is the lifting area times the head: a 12 in. cube under a 12 in. head needs about 450 lb of weight (pp. 97-99); a core lifts with the weight of the iron it displaces (pp. 101-104). Flow-off risers at half height cut the weighting by a quarter (p. 110).

Shrinkage, crystals and heads (pp. 63-88, 148, 243, 264, 282)

  • Crystals set perpendicular to the cooling face; sharp changes of section leave planes of weakness, and a riser or "feeding head" keeps hot iron against the central plane that shrinks last (pp. 72-75).
  • Equal thickness does not cast straight: a plate is made thicker at its edges and thinner along its diagonals, which cool last, and ribs are made a quarter thicker than the plate (pp. 77-81).
  • Heads carry the dirt: a 3 ft x 6 ft loam cylinder is cast "with head cast on 6 inch deep to receive the sullage" (p. 148, Fig. 128); the dry-sand steam cylinder has a head on its top end (p. 243); a 16 ft gun has a 3 ft sinking head (p. 264); a roll's feeding head is the size of the neck and 12-15 in. deep, and the whole heat is run through the mould into a pig on the floor to carry away "the sullage and cold iron" (pp. 282-283).
  • Kettles and pans are lifted out of their casings "as soon as it is safe to do so, on account of danger from shrinkage" (pp. 186, 189).

Pouring (pp. 69-70, 79-80, 182, 189, 232, 235-236, 266)

  • Green-sand castings are poured as cool as will fill (pp. 69-70, 235); dry-sand and loam moulds take the hottest iron, and "the soundest castings are those which are poured with the hottest iron" (p. 236).
  • "Hot iron and rapid filling of the mould is indispensable": metal crossing a plate loses its heat to the mould, so gates are set round it to keep it moving (pp. 79-80). Kettles are run "at a lively rate" (p. 182) with the runner "full from the beginning" (p. 189); dull iron in thin parts waits on the heavy parts and "the connection is lost at that part, and very often the casting as well" (p. 235).
  • Gates spread round a cylinder break up the scum; the riser stays plugged until the iron reaches it (pp. 158, 163, 248). Two ladles on separate runners are better than one for a large elbow (p. 232).

Sand, loam and cores (pp. 121-146, 152-160, 237-242, 302-303, 310)

  • Three mould classes: green sand, cast damp; dry sand, dried in an oven before casting; loam, bricks and loam struck with a sweep and dried (pp. 147-148, 233).
  • Old or floor sand is reused for backing, cores and filling (pp. 133, 213, 280, 302). Facing is a fresh mixture per mould; green facing carries sea-coal (p. 310). A heap "very rotten on account of a preponderance of burnt sand" wants new sand mixed in (p. 303), and the one-heap dry sand for pipes and cylinders needs "constant renewal" (p. 242).
  • Core sand mixture No. 5, "the best dry-sand facing for ... cylinders, pumps, etc., up to 40 inches": 8 parts fire-sand, 2 of moulding sand, 1 of flour, thick clay-water (p. 124). Pipe cores of it let the pipe be gated on top (p. 125). Loam for cores on barrels: 5 fire-sand, 2 moulding sand, 1.5 manure (p. 125). Cores are dried in ovens; a 12 x 10 x 10 ft oven needs one 4 x 3 ft fire (pp. 52-62).

Steam cylinders, pumps and bored work (pp. 70-71, 124, 157, 171, 175-179, 234-263)

  • Steam cylinders and "all castings demanding a clean, hard face when finished" are poured from compact gray iron with plenty of scrap, best run into pigs and remelted first (p. 71).
  • Cylinders and pumps are made in dry sand or loam. Green facing on "pumps" and "cylinders" is "a comparative failure" (p. 241); green moulds leave dirt and scum on "bored surfaces" (p. 171); in green sand the question is not "How can we best secure a clean bore?" but how to avoid scabbing (p. 236).
  • The cylinder is bored: a core pressed in by the head gives "considerably more work in the boring" (p. 157), and port cores are set back so the fin can be broken through "after the cylinder has been bored" (p. 255). The steam chest, ports and exhaust are cored into the casting (pp. 250-255), jackets by caged jacket-cores (pp. 256-263). "Ordinary cores are not to be thought of for this class of work" (p. 250).
  • The water end of a high-duty pumping engine is one loam casting of 8-10 tons with its valve cores in it (pp. 175-179). The machinist's work on a casting is "the parts which have been prepared for external fittings; also bored surfaces" (p. 171).
  • Condensers, tanks, hot-wells and cisterns are cast whole in loam, 1 in. thick for a 4 ft 6 in. hot-well (pp. 191-202). Engine builders "invariably have foundries of their own" for them (p. 191).

Pipes (pp. 125, 130-131, 137-142, 209-232, 324-338, 359)

  • Straight pipes, bends, elbows, tees and branch pipes are each cast whole round a core, with flanges or a socket cast on: a 24 in. flanged bend in loam (pp. 209-215), a 24 in. socket pipe on a 14 ft radius in casings (pp. 215-222), a 60 in. elbow on end (pp. 227-232). The bore is the core; nothing is bored.
  • Pipe cores are swept on barrels wrapped in straw rope and loam; shops kept "six to ten men" on jobbing pipes from 2 to 24 in. (p. 142). Pipes up to 18 in. of any form are rammed in green sand from a kit of wedge-shaped half rings (pp. 324-332). Straight socket pipe went to dedicated plants with moulding machines (pp. 335-338). The pipe-weight table runs by core diameter, 2 in. to 10 ft (p. 359).

Wheels, rolls, plates and beams (pp. 70, 80-85, 114-120, 274-324, 369)

  • Spur, bevel and mitre wheels are moulded with their teeth, from full patterns or from a tooth segment on a spindle (pp. 305-324); "no matter how popular the machine-made wheel may be, there will always be a great demand for wheels made from patterns" (p. 312). Wheels untrue from dry-sand tooth cores "crash during the first few revolutions" and have teeth replaced by wrought ones (p. 319).
  • Rolls are swept in dry sand in a spindle flask, one to a flask, cast on end with a feeding head, and are "to be bored or turned" (pp. 274-283). Roll iron is mixed by chill depth, a quarter to seven tenths of each charge being graded scrap or old car-wheel (p. 120 table: 1000 lb No. 4 to 1000 lb low scrap for 10-12 in. rolls).
  • Castings "which have to resist impact, such as hammers for forges" are made from close No. 3 iron (pp. 70-71). Beams, lintels and girders loaded across are cast, with webs proportioned to cast straight (pp. 48, 81, 84-85), and a table gives the load a cast beam carries in the middle of its span (p. 369). Hydraulic cylinders and guns are cast, the gun cooled from the bore by water (p. 264).

Scrap and remelt (pp. 71, 117-118, 283)

  • Scrap from broken rolls and castings "must be worked up" (p. 117); overflows are run into large pigs and "a great saving is effected" (p. 118); spare iron from a roll goes to a pig in the floor (p. 283).

Repeat work and iron patterns (pp. 185-191, 220, 326, 339-349)

  • For many of one pan, the loam is struck on iron "casings" kept rammed in the pit, and "a great number of kettles" come from one set (pp. 186-191). An iron half core-box saves core labour on repeat pipes (p. 220).
  • For a large run of one pipe, halves of the casting are "finished up and pinned together and used for the pattern" (p. 326). A cast-iron pattern is made from a wooden model, a plaster cast or a carved block by ramming it in sand with two copes and a clay thickness (pp. 344-349).