Rose, Modern Machine-Shop Practice (1901)
Books Modern Machine-Shop Practice
Covers J. Rose, "Modern Machine-Shop Practice", Volume I (690 PDF pages, folios to 479). Its contents page names it Volume 1; Volume II is not in hand. Pages below are the book's printed folios. Plates are interleaved, so the PDF offset runs from 32 at the front to 204 at the back. Chapters read: gear teeth (I-III, pp. 1-64), the lathe (VI-VIII, pp. 119-221), driving work in the lathe (IX) skimmed, cutting tools for lathes (X, pp. 254-273), drilling and boring in the lathe (XI, pp. 274-295), shaping and planing (XVI-XVII, pp. 389-425), drilling machines, drills and cutters (XVIII-XIX, pp. 426-447). Skipped: screw threads and fastening (IV-V), examples in lathe work (XII-XIII) beyond the engine-cylinder and roll passages, measuring machines and tools (XIV-XV), hand drilling and boring tools (XX, pp. 448-450) and thread cutting (XXI). PDF pages 2-6, 8-10 and some forty plates (among them 60, 119, 129, 176, 312, 327, 449, 538, 544, 554, 562, 571, 585, 598, 623, 630, 634, 677, 684-688) carry no text layer; figures were read from the text that describes them, and pages 258, 273 and 278 were read as images.
What the book says
What the book says
The lathe and its drive (pp. 119-126, 160-162)
- The lathe is "the most important" machine tool and the oldest; drilling, boring and reaming are all done on it, and its tools include those of every other machine (p. 119). Classes run foot, hand, single-geared, back-geared, self-acting or engine, screw-cutting and chucking lathes; the boring lathe and the pulley or fly-wheel lathe are its special forms (p. 119).
- The drive runs line shaft, countershaft with fast and loose pulleys and a belt shipper, a stepped cone on the lathe, then the back gear. A five-step cone gives five speeds in single gear and five more in back gear (p. 126). The cone steps should be wide enough to drive the heaviest cut without the back gear, and the countershaft cone matches the lathe cone (p. 162). A pulley lathe's countershaft carries friction pulleys at 110 and 425 rpm for eight changes of speed (p. 160).
- Lathe spindle boxes are lined with babbitt (p. 124); ball bearings appear only as thrust collars.
Special lathes: rolls, pulleys, cylinders (pp. 215-221)
- A 12 ft pulley of 8860 lb was bored and turned in 17 h on a vertical boring and turning mill (p. 215).
- Chilled rolls: the roll runs in its own journals, which are first turned in a separate lathe. A plunge tool is fed its full length at 2-1/2 to 5 ft/min, dry; the tool has four edges and each carries at least one cut (pp. 215-216).
- "When work of considerable weight requires to be bored ... it is more convenient that it remain fixed upon a table, and that the boring tools rotate" (p. 218).
- The cylinder boring machine bolts the cylinder to a table; a worm-driven bar turns and the cutter head traverses the bar by a feed screw inside it. The Sellers machine carries face plates with slide rests that face both cylinder ends while the bar bores, and its rigidity allows a very coarse finishing feed with less tool wear (p. 219). The quartering machine bores both crank-pin holes of a driving wheel pair at once (pp. 219-221).
Cutting tools (pp. 254-273)
- Cutting tools are "a fine grain of cast steel termed 'tool-steel'", hardened at a red heat in water and tempered (p. 254). Neither wrought nor cast iron appears as a cutter anywhere in the volume, and self-hardening steel is not named.
- Rake follows the metal: wrought iron takes top rake, cast iron less, brass none or negative (pp. 255-256). How long a tool lasts, and how heavy a cut the lathe will drive, depend on the grinding; skilled men vary the angle at every grind (p. 258). Chilled cast-iron calender rolls are cut at about 7 ft/min with a 75 degree tool (p. 258).
- The chips judge the cut: wrought-iron cuttings should come off almost too hot to hold, with water dropped at about three drops a second; short, uncoiled cuttings mean too little rake, and a tool that dulls fast has too much clearance (p. 259). The spring tool finishes cast iron with water at about 7 ft/min (p. 264).
- Grinding the top face lowers the tool, so tool holders carrying short cutters are used; with them "about 200 of the tools or cutters" serve 24 lathes a week, and only the end face is reground (pp. 261, 271). A disc cutter "may be reground until the circumference of the wheel is used up" (p. 273).
- Hartig's constants, horsepower per lb of cuttings removed per hour (p. 273, read from the page image; the lathe figure for steel is printed as .4470):
| Metal | Lathe | Planer |
|---|---|---|
| Cast iron | .0314 | - |
| Wrought iron | .0327 | .0520 |
| Steel | .4470 | .1120 |
| Gun metal | - | .0127 |
Drilling, reaming and boring (pp. 274-295)
- Twist drills: Morse taper of 5/8 in. per foot; each edge at 60 degrees to the axis, 45 for brass or cored holes; the outer corner dulls first; drills are ground in a machine (pp. 274-277).
- Duty of a 1/2 in. drill through 2-3/4 in. of hammered scrap iron: nearly 20 ft/min, 100 revolutions per inch of feed, soap and water, 1 min 20 s a hole, "120 to 130 such holes" before resharpening, and about 1/64 in. ground off to restore it. At 75 revolutions per inch it gave 70 holes. Upward of 3000 holes 3/4 in. by 1 in. in steel came off one drill without regrinding; a hard steel rail at 22 ft/min "distressed the drill" (p. 278).
- The reamer is fed at 15-18 ft/min (p. 281). It wears from the first hole; it is restored by upsetting the teeth with a set chisel, or an adjustable reamer takes up the wear; the wear limit for work that must fit is 1/1000 in. (pp. 283-284).
- The hard skin of a casting dulls a boring tool, so the first cut goes beneath it (p. 286). Rough with the boring tool and finish with a cutter at slow speed and coarse feed (pp. 286-287).
- Boring bars: a fixed-cutter bar is twice the length of the work; a sliding head is shorter and stiffer; drive from both ends. Three cutters bore out of round, four do not, and a four-cutter head feeds four times as fast (pp. 289-291). Sellers car-wheel cutters bore "from 50 to 250 car wheels, without appreciable reduction of size"; they are hardened at the ends and restored by peening the soft middle (p. 289). A cannon is bolted to the lathe carriage and fed to the bar (p. 292).
- When the tool rotates and the work stands, the cutting speed is at its lowest, "rarely exceeding 18 feet per minute" (p. 294).
- Roughing speeds and feeds (p. 294), feed as lathe revolutions per inch of tool travel:
| Metal | Roughing speed, ft/min | Feed |
|---|---|---|
| Wrought iron | 40 at 1/2 in. down to 25 at 6 in. | 30 to 20 |
| Cast iron | 45 at 1 in. down to 30 at 6 in. | 30 to 14 |
| Brass | 120 to 65 | 25 |
| Tool steel | 24 to 18 | 60 to 25 |
Finishing feeds are 60 and 50 for wrought iron, 40 to 12 for cast iron, 40 for brass.
- Regrinding against speed: a tool that cuts 12 in. in 20 min and then takes 4 min to regrind is better run fast and ground after every foot; a finishing cut must carry its whole length without a regrind. Take the metal off in one cut at about 35 ft/min rather than two at 40 (p. 294).
- Workmen differ by 30 per cent in speed and 50 in feed; Hartnell found 100 to 200 per cent, and fly-wheel rims tooled at 2 to 8 sq ft an hour. Pratt and Whitney automatic lathes run one man to several machines at 200 revolutions per inch of feed. A harder metal, a shallower cut or a finer feed takes more power per lb removed (p. 295).
Shaping (pp. 389-401)
- The shaper's place "is not as important as was the case a few years ago, because of the advent of the milling machine" (p. 389). Its apron lifts on the return stroke, and the feed takes place at the end of the return (pp. 390-391, 398).
- It cuts keyways in shafting held in its chuck or between shaper centres, and indexes by a worm and sleeve (p. 397). Stroke is limited to about 18 in., 12 on small machines (p. 397).
- Shaping is quicker than planing because the shaper's cone varies the speed, "whereas in a planing machine the cutting speed of the tool is the same for all sizes of work, and all kinds of metal" (p. 398). The return stroke is about 40 per cent quicker than the cut, by crank, link or Whitworth quick return (pp. 398-401).
Planing (pp. 402-425)
- The table runs on V-guides driven by a rack; the cross slide rides the uprights. Two loose pulleys and one fast pulley take an open and a crossed belt; dogs on the table shift the belts at each end, the larger countershaft pulley gives the quick return, and the feed acts at reversal (pp. 402-403). The Sellers planer lifts the tool on the back stroke and its return ratio equals the ratio of its countershaft pulleys (p. 406). Open-side planers return at 4 to 1 and 3 to 1; post planers cut at 4, 8, 12 and 16 ft/min (p. 411).
- Two heads, roughing and finishing, double the output (p. 405). With a double apron the finishing tool lasts "to finish a great many pieces without being disturbed", and the reground roughing tool is set to the last roughing cut (p. 413).
- A long casting is balanced on wedges and its foundation face planed first (p. 420). Planer tools take at most 10 degrees clearance, 5 for broad finishing tools, and less front rake for steel than wrought iron and for cast iron than wrought (pp. 424-425).
Drilling machines, drills and templates (pp. 426-445)
- The drill press has a cone pulley, back gear for large drills and boring bars, a feed cone and a counterbalanced spindle; the feeds are finer without the back gear (p. 430). A combined drilling and boring machine has horizontal and vertical spindles and eight speeds (p. 432). The horizontal machine "can rough out with a fine feed and finish with a light cut and a very coarse feed" (p. 434).
- A four-spindle machine with a rotating table drills, enlarges, countersinks and reams one hole in turn, "the four operations proceed together" (p. 435).
- Boiler shells: drills at 34 ft/min under soapsuds at 60 lb, about 20 holes an hour per drill; a 14 ft boiler end flange turned in about 2-1/2 h (pp. 435-436).
- Jigs have hardened bushes and limit gauges (pp. 439-440). Locomotive cylinder cover and flange holes are drilled through a template ring, clearing holes first and tapping holes after; the steam-chest studs use a template; the steam ports are cut on the drilling machine by a cutter through a false plate and sliding die in "thirty minutes" a cylinder (pp. 440-442).
- The flat drill stands rough use and its diameter is restored by forging; the twist drill is the better tool (pp. 442-443). Soapy water on wrought iron; brass, cast and chilled iron dry. Drills are tempered orange to purple, straw for hard metal (pp. 444-445).
Gears, cast and cut (pp. 2, 34-64)
- "Wheels that require to run without noise or jar, and to have uniformity of motion, must be finished in gear-cutting machines, because it is impracticable to cast true wheels" (p. 34). Involute teeth are cut at one passage of a revolving cutter (p. 34); the Warner and Swasey engine generates them with rack-form cutters (p. 36); the Corliss bevel cutter follows a former (p. 45). Cut teeth carry less clearance than cast (p. 2).
- Large wheel patterns have separate arms, hub, rim and teeth; pinions of 6 in. and under are made from a solid piece (p. 54). Mortise wheels take wooden cogs, the larger wheel cogged since the pinion wears most (pp. 63-64). Cast wheels are kept in stock at standard pitches (p. 64).
Gaps
- Neither wrought nor cast iron appears as a cutter anywhere in the volume, and self-hardening and high-speed steel are not named. Every cutting tool is crucible tool steel, hardened and tempered (p. 254); drills differ by temper, not by metal (p. 444).
- Wilkinson's boring mill of 1774 is not named.
- The book names the milling machine as displacing the shaper (p. 389) and ranks the lathe first and oldest, with boring and drilling done on it (p. 119).
- Teeth are cut by revolving or rack-form cutters on gear-cutting engines (pp. 34, 36, 45); the shaper cuts flats and keyways (p. 397), not teeth.
- The shaper and planer return faster than they cut: about 40 per cent on the shaper (p. 398), 3 or 4 to 1 on the planer (p. 411). The planer's pulleys are two loose and one fast (pp. 402-403).
- A cylinder's outside is left as cast; the cylinder is bored and both ends faced at one setting (p. 219).
- Planer and lathe shed cuttings and turnings (pp. 259, 273); scale is the skin of a casting and dulls the tool (p. 286).
- Reamers shrink their holes from the first one (p. 283), and a dull boring tool bores a taper (pp. 286-287).