The anvils of the belly helve, the tilt hammer and the steam hammer
Books Metallurgy: Iron and Steel, The Manufacture of Iron, The Iron-Founder
Covers how the period books show the anvil block, anvil and renewable face of lever hammers (a), the steam hammer's anvil block and die (b), and how such blocks were cast and finished (c). Read
- Percy, Iron and Steel (1864), through its OCR text (44 hits for
anvil). Folio = PDF page less 20 here. Read folios 694-698 (belly helve, steam hammers, Nasmyth) and 594-595 (Lancashire hammer). Figures viewed: PDF 714 (fig. 175), 716 (fig. 176), 717 (fig. 176a); the scan of fig. 175 is poor. - Overman, Manufacture of Iron (1850), searched for
anvil(20 hits). Folio = PDF page less 6. Read folios 336-342 and 383-384. Figures viewed: PDF 342 (page text; fig. 97 is the helve ring), PDF 346 (fig. 100 caption only, the drawing is a small plate not described here). - Fairbairn (both volumes), Bolland (iron founder), Rose, Marks, Hamilton: searched for anvil, helve, tilt hammer, hammer block, sow, dovetail, chill. Fairbairn II (PDF less 42 = folio) mentions an anvil only in passing (folio 255 puddler's ball thrown on the anvil; folio 268 a works scene); Marks has two uses of "anvil" for a welding swage; Bolland, Rose and Hamilton give nothing on hammer anvils. None was read further.
(a) Belly helve and tilt hammer
- Percy folio 694: "Helves are now entirely made of cast-iron, with shifting wrought-iron striking faces." Classes: the tilt hammer (pivot between block and cam; blocks 1 to 5 cwt) and the helve, head-lift or belly-lift (cam between the pivot and block). Belly helve: "the anvil stands in front of the rotary cam shaft ... and leaves three sides free for working" (folio 695).
- Percy folio 694, fig. 175 (Mersey Steel and Iron Works belly helve, 10 t casting, T in plan, 10 t moving mass, lift 18-24 in., 60 strokes/min): "The hammer face is made of wrought-iron, and is attached to the helve by a dovetail-groove and wedge; the anvil is faced in a similar manner." The small dovetail-groove near the helve's centre likewise seats the lifter, "easily shifted and replaced when worn out". The figure (plan, side, front and end elevations, a scale in feet) is too small and blurred in this copy to read the anvil's dimensions from; the anvil is not drawn apart from the helve.
- Percy folio 695: "an ordinary hammer face in constant work will only last from three to seven days ... and the anvil face, under similar conditions, will last about the same time." Water-cooled faces last ten times longer (Arkinstall) but "has been generally abandoned".
- Percy folios 594-595, fig. 191 (Lancashire forge hammer, water wheel): "The anvil is a solid block of white cast-iron. It rests upon a wooden block, the anvil block, square in section, with the angles rounded off", four equal timbers with the fibre vertical, bound with wrought-iron hoops; that stands on a foundation of timbers laid horizontally, "forming an elastic bed and acting as a spring, without which the iron would break on being hammered out"; around the block a wood frame filled with finery cinder stamped solid. Head 7 cwt, lift 2 ft, 100 blows/min.
- Percy folio 293 (Catalan forge): the anvil is a wrought-iron piece 2 ft 3.56 in long, 9.84 in broad in the middle, 8.66 in at each end; "by means of a projecting piece, or tenon, about 5.12 in deep, and of the same breadth, it fits into a heavy block of cast-iron, supported by, and wedged into, a large block of stone".
- Overman folio 336 (a helve hammer): "The anvil, a cast iron block, about the weight of the hammer; but it may be of less weight if the iron stock is employed. A log of wood from six to eight feet in length, and frequently four feet in diameter ... secured at its base and top by iron hoops. It rests upon timber laid across piles very stoutly driven in the ground ... because rock, or the most solid ground, forms at best but an insufficient base."
- Overman folio 337-338 (T hammer): the whole machine is cast iron except the timber foundation below ground, 30 to 40 t; hammer 4-5 t, "anvil stock" 5-8 t, cam ring 3-4 t.
- Overman folio 340, g (faces): faces are "more or less broad according to the width of the hammer"; small hammers 1.5 to 4 in wide, the T or steam hammer's at least 5 in. "The anvil and hammer face of a steam or T hammer is almost a square plate, twenty inches in length, and sixteen in width. For shingling ... a face an inch in height is raised in the middle of the plate, and runs across ... a second face is raised on the half of the anvil, running at right angles to the first" for stretching or drawing; for machine iron the cross face is extended both sides.
- Overman folio 342 (crank-driven lever machine before the squeezers): "The anvil d is about two feet in length, and from twelve to fourteen inches in width; it is a movable plate, at least three inches thick, which, if injured, can be exchanged for another"; hammer face of plates screwed on, in parts 8 to 10 in wide against breakage by expansion; the whole machine cast iron, 4 or 5 t.
- Overman folio 383-384: cast iron hammers and anvils, "if made of good cast metal, are sufficiently hard and smooth" for horseshoe, tire and heavy bar; for fine iron or steel, wrought iron ones "furnished with well-hardened and polished steel faces"; steel is not welded to a large piece, "it is more profitable to insert the steel, in a separate piece, into a groove made in the hammer face, and in the anvil, and to fasten it by means of wedges".
(b) Steam hammer
- Percy folio 698, Nasmyth 15 cwt double-acting hammer, Atlas Works, figs. 176, 176a: hammer-block 15 cwt, stroke 40 in; "The weight of the anvil is about 5 1/2 tons: it rests on a bed formed of 16 upright square baulks of timber of a total content of about 84 cubic feet. The sole-plate measures 9 ft 9 in by 7 ft 1 in ... it rests upon a bed of broken cinders. A clear space of 1/16 of an inch is left all round the anvil, where it passes through the sole-plate." Hammer standards are held to the sole-plate by wrought-iron and wooden wedges over wooden packing and holding-down bolts.
- Percy folio 698: "A swage face ... is fixed to the anvil instead of the ordinary flat face piece when the hammer is used for forging round bars" - the face piece is a separate, changeable plate.
- Fig. 176 (PDF 716, front elevation, viewed): the anvil is a tall, upright iron mass, narrow in the front view, rising through the sole-plate between the standards, its head a broad flat block under the hammer-block; below the sole-plate it stands in a deep pit with sloping sides, the pit labelled as hard-down filling, on a layer of upright timber baulks over "hard subsoil"; an iron plate or cap lies between the anvil's foot and the baulks.
- Fig. 176a (PDF 717, viewed): item 3, the anvil's end elevation: a square-sectioned shaft whose foot flares out in straight sloping sides to a wide base; a thin wide flange or plate at the top (the sole-plate level) and a narrower top block carrying the face piece. Item 1, plan: the anvil head is a rectangle longer across the hammer standards, with a rectangular face piece seated in its top; in the plan the sole-plate has the hammer standards at both ends and four bolt holes.
- Overman folio 338: the steam hammer's anvil is not described apart from the text above ("the steam hammer, before mentioned").
(c) Casting and finishing
- Percy folio 594: the Lancashire hammer's anvil is "a solid block of white cast-iron" (a casting, not wrought up). Overman folio 336: "a cast iron block"; the T hammer's anvil stock is cast with the machine (folio 337).
- Percy, Overman: faces of cast iron work "sufficiently hard and smooth"; wrought faces, steel inserts set into a groove with wedges for fine work (Overman folio 383-384).
- Bolland, the iron founder (chapters on chilled work, p. 128-133 of the PDF): chilled castings are for wheel rims and rolls, "chilled almost 1 inch deep"; no hammer anvil or hammer block is named.
What the sources leave open
- How an anvil block was cast: pit or open sand, face up or down, chills on the face, runner and feeding head - not stated in any book read.
- How the dovetail was formed or finished (cast in and chipped, or cut), and whether the face seat was planed - not stated.
- Dimensions of the helve or tilt-hammer anvil proper (Mersey fig. 175 is unreadable); the mass relation hammer to anvil beyond "about the weight of the hammer" (Overman), 15 cwt to 5.5 t (Nasmyth, about 7 to 1).
- The die block's fixing on the steam hammer anvil: "face piece", "swage face" named, with no stated dovetail or key.
- The proportions of the pad and its tenon, wedge size and number.
- The anvil's height above the sole-plate and the pit's depth (fig. 176 has no dimensions in this scan).