Johnson, Blast-Furnace Construction in America (1917)

Books Blast-Furnace Construction in America

Covers J. E. Johnson Jr., "Blast-Furnace Construction in America" (1917, 441 PDF pages). The scan has no text layer on PDF pages 2-441; the whole book was read from an OCR of 200 dpi renders. Pages below are the book's printed folios, which are the PDF page less seventeen. The chapters, checked against the book's own contents list (whose folio for chapter VI reads 220, an OCR misread of 233): introduction (pp. 1-6), I handling raw materials (p. 7), II filling (p. 48), III the boiler plant (p. 99), IV blowing apparatus (p. 119), V hot-blast stoves (p. 190), VI the stack (p. 233), VII cleaning and washing the gas (p. 285), VIII iron and cinder (p. 328), IX auxiliaries and plant arrangement (p. 359), X dry blast (p. 383), index. Read in full: the introduction and chapters II, V, VI and VIII, and the history, gas and arrangement parts of III, VII and IX. Skimmed: ore docks, bridges and unloaders (ch. I), boilers, blowing engines and turbo-blowers (chs. III-IV), gas washing (ch. VII), dry blast (ch. X). The plates read by eye: Fig. 25 single bell and hopper (p. 48), Fig. 126 Glendon iron-pipe stove (p. 194), Figs. 130-133 McClure three-pass stove (p. 202), Fig. 157 chimney valve (p. 220), Fig. 163 section of a skip-filled furnace (p. 239), Fig. 164 hearth and bosh (p. 240), Fig. 167 charcoal furnace with steel bosh jacket (p. 253), Fig. 176 bustle pipe, penstock and blow pipe (p. 279), Fig. 178 gas outlets and dust catcher (p. 290), Fig. 179 early dust catcher (p. 292), Fig. 212 cast house (p. 332). The stove tables on pp. 230-231 did not OCR legibly and were not used. Subject the plant as built - shapes, parts, proportions, what is on the machine - for the blast furnace and its bell top, the stove, the stack, the blower, the canal and the casting bed. Johnson's companion "Principles, Operation and Products" covers operation.

What the book says

The plant (pp. 4-6)

  • A ton of iron takes about 2 t ore, 1 t fuel and 4 t blast, and gives about 5.5 t gas (p. 6).
  • Cold-blast charcoal slag "is not heated hot enough to run freely and has to be removed from the furnace with ... slag-hooks, etc., or, if it comes from the furnace without assistance, it chills before going more than a few feet" (p. 4).

Charging and the top (pp. 7-16, 48-98)

  • Old charcoal furnaces stood against a hill, with a bridge from the stock house to the top, and barrows were wheeled across (pp. 7-8). Power hoists came when furnaces grew from 25-30 ft to 50-70 ft (p. 9). The two-wheeled filling barrow carried about 1500 lb (pp. 13-14), and stayed "almost universal" after the top was closed (p. 48).
  • The bell and hopper was the first closed top and stayed in use (p. 48, Fig. 25): an inverted-cone hopper whose turned lower edge seats on a turned bell; the charge is dumped into the annular space and slides in when the bell drops. The bell slopes about 45 deg (p. 53). Early bells were worked by a hand crab, later by a steam cylinder, counterweighted so the bell stays shut (pp. 87-89). A bell lasts about a year (p. 93).
  • Filling one side ruins the furnace; the charge must fall evenly round the circle (pp. 49-51). A leaking bell lets gas burn through the top (p. 60). A gas seal (a second bell) saves 3-10 % of the gas lost at each dump (p. 59).
  • Skip filling first succeeded on a large scale at the Edgar Thomson works under men still in office in 1917 (pp. 61-62). The skip dumps by running onto bent rails that tip it past 45 deg (p. 42; Fig. 163, p. 239, shows the incline, the transfer car and the scale car).
  • The stock line was found with a test rod, later a recorder whose saw-tooth chart shows each charge and each slip; a slip drops the stock line 2-20 ft (pp. 93-97).

Blowing and gas use (pp. 99-100, 119, 172-175, 285-296)

  • Blowing was by water power first, then steam (pp. 99, 119). Anthracite needs "so much greater" pressure than charcoal in a furnace of the same size (p. 99).
  • The open top burned "in a great flame, visible at night for miles; this is the case at a few cold-blast charcoal furnaces to this day" (p. 100; again p. 285, "for centuries").
  • Before the closed top, furnaces carried a small pipe stove on top over the throat, drawing the top flame through it; a furnace on that hot blast beat a symmetrically filled cold-blast furnace (p. 100). Next, flues just below the stock line drew gas to a chimney through boilers and stoves (p. 285). Stoves were at first fired with coal (p. 285).
  • The top gas is about 25 % CO (p. 286). Its fume "gives the gas its characteristic appearance, so that an experienced furnaceman can tell more quickly by looking at the gas discharging from the boiler and stove stacks than by any other way if his furnace is working 'hot' or 'cold'" (p. 286); the fume is white on a good-working furnace (p. 287).
  • Early furnaces had one gas outlet; four is usual, "three properly located are sufficient" (p. 287). Explosion doors sit high on the outlet pipes (pp. 288-290, Fig. 178).
  • The early dust catcher (Fig. 179, p. 292): the downcomer runs straight down into the centre of a steel cylinder, the gas turns back up to an outlet in the side, and the dust falls into a cone emptied through a bell valve at the bottom. Later catchers add a tangential inlet (p. 293).
  • A gas-driven blowing engine needs gas scrubbed well past primary cleaning (pp. 172-175).

Hot-blast stoves (pp. 190-232)

  • Neilson, 1828; the first trial gave 80 F (pp. 190-191). The first stoves were coal-fired iron pipes, then pipes over the furnace top, then on the ground once the top was closed (pp. 191, 285).
  • The iron-pipe stove (Fig. 126, p. 194): a brick chamber with a combustion chamber at one end and the stack at the other; elliptical U-pipes stand on bed pipes between baffle walls, and the blast runs through the pipes. It reaches 850-1000 F, about 900 F being the limit of the pipes (pp. 192-200).
  • The firebrick stove: Whitwell built "cylindrical chambers with a top either cylindrical or dome-shaped"; "the shell of these chambers was of iron (now steel) plate, riveted together air-tight" (p. 192), filled with brick checkers. Four connections: gas burner, chimney, cold blast, hot blast (p. 192).
  • The McClure three-pass stove (Figs. 130-133, p. 202): a plate cylinder with a dome, a central combustion flue, concentric rings of checkers, and its own short stack on the dome. Two-pass stoves keep their valves at ground level (pp. 201-205). Height is four to five times the diameter (p. 200).
  • Valves: a hot-blast mushroom valve on a water-cooled bronze seat, a cold-blast slide valve with a small equalizing port, a gooseneck burner, chimney valves, a blow-off valve (pp. 209-220). Stoves draw by stack, and a battery shares one (pp. 222-223).
  • Flue dust slags the combustion-chamber wall in 8-9 months; checker openings are 9 in with dirty gas, 6 in with clean (pp. 224-225).
  • Count (pp. 226-227): one pipe stove can serve; firebrick stoves need at least two. "Furnaces were originally operated with only two stoves of this type ... Less than three are never contemplated, four is only ordinary good practice, and five have been installed with extremely satisfactory results." The reasons are a stove in reserve and the blast temperature, which falls while a stove is on blast; with two "these variations are so great as to cause serious irregularities". A third stove doubles the time on gas and gives a "soaking heat".
  • The blast falls 50-150 F between putting a stove on and taking it off; a cold-wind valve from the cold main into the hot main evens it (pp. 227-228). A stove is about the bosh in diameter and at least the furnace in height, up to 20-25 % more (p. 228).

The stack (pp. 233-284)

  • Cold-blast hearths ran at 2200-2400 F (p. 233). Early stacks were stone truncated pyramids 20-40 ft high with a 6-8 ft bore, built into a hill, with one tuyere under an archway; later an arch in each side, three for tuyeres and the fourth for the forehearth and tapping hole (p. 237).
  • The modern stack: a plate shell on a mantle ring over columns, about 4 ft of brick, a firebrick bottom (pp. 237-238, Fig. 163). The hearth holds 60-150 t of iron and 20-40 t of slag (p. 240).
  • Fig. 164 (p. 240): the tuyere centre line over the cinder notch, the cinder notch over the hearth level, cooling plates staggered through the bosh.
  • The tuyere projects about a foot into the furnace, its nose 3.5-4 ft in from the outside of the brickwork; the blast "mushrooms" back against the wall (pp. 245-246).
  • Johnson's charcoal furnace (Fig. 167, p. 253): a steel bosh jacket, a bustle pipe round the bosh on the columns, a small bell and hopper, and two gas offtakes curving off the top.
  • Stock-line armour of wrought-iron angles (pp. 258-261); the coned top with raised gas outlets, and the wheelway for barrows on hand-filled tops (p. 262).
  • Blast delivery (pp. 278-284, Fig. 176): a brick-lined bustle pipe, a gooseneck penstock, a blow pipe on ball joints, a bronze cooler and a copper tuyere. The wicket has a hole for a pricking rod, closed by a fitting with "a peep glass through which the action of the tuyere can be directly observed" (p. 283). In trouble the blow pipe is dropped and slag flushed out through the tuyere (p. 281).

Iron and cinder (pp. 328-358)

  • Iron was first run into puddles; the runner (the sow) with side runners gave the pig; a bed is a branch runner with its pigs at right angles (p. 328). The sand must be coarse and free of clay (pp. 328-329). Pigs were broken from the sow hot with a bar, or cold with sledges (pp. 330-331); Fig. 212 (p. 332) shows a cast house with a crane lifting a whole "comb" out of the sand.
  • Iron and cinder leave the taphole together late in a cast and are parted by a skimmer and dam in the trough (pp. 344-346). Liquid slag practice came with hot blast (p. 346). Slag ran into its own long semicircular runners in coke breeze, broken with hooks into 3-4 ft pieces (p. 347).
  • A magnetic separator won 15-25 t of iron a month from slag (p. 358).

Plant arrangement (pp. 359-382)

  • A furnace takes 1200-2000 gal of cooling water a minute (p. 359); tuyeres burn if the water stops for two seconds (p. 366). ("Blower" on pp. 376-378 is the man in charge, not the machine.)
  • Furnaces stand in pairs with the stoves in a row or at the corners of a square (pp. 373-378, Fig. 238); about four furnaces is the limit from one engine house (pp. 380-381).
  • Slag runners are kept short, because the cinder builds in the trough and the labour grows almost as the square of the length (p. 382).