Truran, Overman, Percy, Fairbairn, Wilson, Courtney, Marks and Rose on wrought-iron stock sizes and weights, about 1840-1880
Books The Iron Manufacture of Great Britain, The Manufacture of Iron, Metallurgy: Iron and Steel, Iron, its History, Properties and Processes of Manufacture, Treatise on Mills and Millwork, Part II, A Treatise on Steam Boilers, The Boilermaker's Assistant, The Manufacture of Iron and Steel Tubes, Modern Machine-Shop Practice
Figures are what the books state; INFERRED marks arithmetic or a reading of mine.
Sources
Page numbers are the printed folio; the PDF page is given as an offset. Wrought iron is taken at 0.282 lb per cubic inch (INFERRED from the rule below: 40 lb per square foot per inch of thickness).
- Truran, The Iron Manufacture of Great Britain (1862). PDF = folio + 26. British.
- Overman, The Manufacture of Iron (1851). PDF = folio + 6. American practice.
- Percy, Metallurgy: Iron and Steel (1864), no text layer. PDF = folio + 20. The price list pp. 749-760 (Messrs. William Bird & Co., prices of 1863) was read from page images at 110 dpi; the OCR text loses the fractions. Re-read from PDF 773-780 (folio 753-760) at 130-500 dpi: the W.G. numbers, the cwt and foot figures and the rivet and round sizes are clear; a fraction printed in the scan's small type is marked (read) below. The puddle-bar paragraph is on folio 709 (PDF 729), not 700.
- Fairbairn, Iron: its History, Properties and Processes of Manufacture (1865). Text read from the archive.org OCR; the PDF itself has no text layer. Fairbairn, Mills and Millwork Part II (1863), repeats pp. 257-259 (PDF = folio + 42 from p. 184).
- Wilson, A Treatise on Steam Boilers (1873), OCR text.
- Courtney, The Boilermaker's Assistant (1880 ed.). PDF = folio + 10.
- Marks, The Manufacture of Iron and Steel Tubes (1903).
- Rose, Modern Machine-Shop Practice (1901), for the Birmingham wire gauge.
Not read in full: Hawkins (steel era, no stock sizes found on the pages that name boiler plate), Spencer, Campbell, Fairbairn Useful Information (experiments only).
Weight rules (Courtney p. 95)
"Thickness of plates in 1/8 parts of an inch multiplied by 5 = lbs. weight per square foot." "Area of section of flat bars (in inches) multiplied by 3.33 = lbs. weight per foot of length." "Diameter of round iron in inches squared multiplied by 2.64 = lbs. per foot of length." (OCR and page image read; fractions typeset as 1/8.) INFERRED: 1/4 in plate is 10 lb per square foot = 48.8 kg per square metre.
Puddled ball and bloom
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| puddling charge | 4.5 cwt of refined metal per heat | 229 | Truran p. 211 | "The general charge is 4 1/2 cwts. of broken refined metal to a heat." | |
| balls per heat | six | Percy p. 656 | "The sixth and last ball was taken out" | ||
| ball weight | about 80 lb | 36 | Percy p. 656 | "A ball weighs about 80 lbs." | |
| ball weight and size | 70-80 lb, 12-15 in across | 305-380 mm | 32-36 | Overman p. 268 | "round balls, twelve or fifteen inches in diameter, or seventy or eighty pounds in weight, are formed" |
| bloom (squeezed) | about 5 in diameter x 18 in long | 127 x 457 mm | Truran p. 219 | "reduced to a bloom about 5 inches in diameter by 18 inches long" | |
| bloom (forged, hammer) | 60-100 lb | 27-45 | Overman p. 334 | "for forging blooms of from 60 to 100 pounds in weight" | |
| squeezer work | 15-20 strokes, about 25 s | Truran pp. 219-220 |
INFERRED: the 5 x 18 in bloom is 353 cubic in = 99 lb = 45 kg solid; Overman's 60-100 lb brackets it.
Muck bar (puddled bar)
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| finishing-roll grooves | flat bars 3-7 in wide, 1/2 to 1 1/2 in thick | 76-178 x 13-38 mm | Truran p. 223 | "flat bars from 3 to 7 inches wide by 1/2 inch to 1 1/2 inches thick" (page image, PDF 249; was read "3/8 to 1 1/4" from the OCR) | |
| bar, Mills II | about 4 in wide, 3/4-1 in thick, 10-12 ft long | 102 x 19-25 x 3050-3660 mm | Fairbairn Mills II p. 257; Iron p. 123 | "reduced to about 4 inches wide, three quarters to an inch thick, and 10 or 12 feet in length ... called a puddle-bar" | |
| bar, merchant and rail work | 3 in x [thickness unread], 15-18 ft; 5 in x [thickness unread], about 14 ft | 4.6-5.5 m; 4.3 m | Percy p. 709 | "puddled bars have generally the following dimensions: 3 in. by [fraction] in., and from 15 ft. to 18 ft. in length; and 5 in. by [fraction] in., and about 14 ft. in length". The two thickness fractions are blobs in the scan even at 1000 dpi (PDF 729); the archive.org OCR reads them "1/4" and "3/8" and I cannot confirm either. Truran's finishing grooves (1/2 to 1 1/2 in) and Fairbairn's 3/4-1 in make a bar this thin doubtful: use Truran, not these two. | |
| bar, for plate and sheet | 6-15 in wide | 152-381 mm | Percy p. 709 | "When intended for sheets and boiler-plates they are rolled from 6 in. to 15 in. wide" | |
| cut length for piling | 3-4 ft | 0.9-1.2 m | Truran p. 226 | "puddle bars of a suitable length, generally from 3 to 4 feet, are placed together to form a pile" | |
| roll speed, shears | 35-80 rpm; shears hot | Truran p. 224 | |||
| finer's bar (charcoal) | about 30 ft x 6 in x 1 1/2 in "often more" | 9.1 m x 152 x 38 mm | Percy p. 725 | "a bar about 30 ft. long, 6 in. wide, and 1 1/2 in. thick" |
INFERRED: Fairbairn's 4 x 0.875 x 132 in bar is 462 cubic in = 130 lb = 59 kg. A 3.5 ft cut length is 41 lb = 19 kg.
Piles
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| pile section range | 3 to 10 in square | 76-254 mm | Truran p. 226 | "the sectional dimension of which varies with the size of iron ordered, from 3 inches to 10 inches square" | |
| large pile | 3 ft 6 in long x 7 wide x 8 high; four to a heat; about 4 cwt each | 1.07 m x 178 x 203 mm | 203 | Truran pp. 226-227 | "7 inches wide, by 8 inches high - a common size for railway bars and the larger kinds of merchant iron"; "Piles of this size weigh about 4 cwts. each" |
| small-merchant pile | 18 in long x 3 wide x 2 1/2-3 thick; 16-18 to a heat | 457 x 76 x 64-76 mm | Truran p. 227 | "piles are made about 18 inches long, 3 inches wide, and 2 1/2 to 3 inches thick" | |
| billets for smallest bars | 12-20 in long x 1 1/4-1 1/2 in diameter; 25-30 to a heat | Truran p. 227 | "billets, measuring 12 to 20 inches long by 1 1/4 to 1 1/2 in their diameter" | ||
| small-iron pack | 40-50 lb; 3 1/2 in x 12 in rough bars | 18-23 | Overman p. 354 | "seldom more than forty or fifty pounds" | |
| rail pile | 300-500 lb for an 8 yd rail | 136-227 | Overman p. 359 | "a pile of from 300 to 500 pounds of iron" | |
| rail pile make-up | 6-7 in x 1 in No. 2 iron top and bottom, 18-20 puddle bars 3-3 1/2 in wide between | Truran p. 228 | |||
| boiler plate pile | puddle bars crosswise in alternate layers, or two blooms hammered together | Truran p. 230 | "rolled from piles having alternate layers laid crosswise" | ||
| faggot pile | box of plate filled with clippings, hammered then rolled | Truran p. 230 | |||
| numbering | No. 1 puddle bar, No. 2 = rolled from puddle-bar piles, No. 3 from No. 2 | Truran p. 227; Percy p. 720 |
INFERRED conflict: 3.5 ft x 7 x 8 in solid is 663 lb (301 kg, 5.9 cwt), against the stated 4 cwt. Either the pile is not solid (interstices) or the 4 cwt is the lighter 'peeler' mix; the book does not say. The small pile solid is 42 lb = 19 kg.
Merchant bar
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| round and square, Staffs | 1/2 (read) to 3 in; extras below 1/2 in down to 3/16 and above 3 in up to 7 in rounds | 13-76 mm | Percy p. 754 | "The ordinary sizes of bar iron are from 1/2 [read] to 3 inches round and square, and from 1 to 6 inches wide by 1/4 [read] to 1 inch thick." Extras by size: 15/32, 7/16, 13/32, 3/8, 11/32, 5/16, 9/32, 1/4, 7/32, 3/16 in at 5/, 10/, 15/, 20/, 25/, 30/, 35/, 40/, 60/, 80/ per ton; 3 1/4 to 3 1/2 up to 4 3/4 to 5 in at 10/-50/; rounds only 5 1/4 to 5 1/2 up to 6 3/4 to 7 in at 70/-130/. | |
| flats, Yorkshire, Newcastle | 1 to 6 in wide by 1/4 to 1 1/4 in thick | 25-152 x 6-32 mm | Percy pp. 755-756 | "from 1 to 6 inches wide by 1/4 to 1 1/4 inch thick" | |
| weight per bar, Lowmoor | extras by weight per bar from 2 1/2 up to 9 cwt | 127-457 | Percy p. 757 | "From 2 1/2 to 3 cwt. each bar ... 8 to 9" | |
| weight limit, Welsh | "Heavier than 6 cwt. per bar special agreement" | 305 | Percy p. 758 | ||
| length, small merchant | 20 ft once enough, 50 ft "not an unusual length", cut into two or three | 6.1 m; 15 m | Truran p. 234 | "Formerly 20 feet was considered sufficient, but now 50 feet is not an unusual length." | |
| length, heavy section | 10-12 in wide up to 50 ft | 15 m | Percy p. 762 | "iron 10 to 12 in. wide can be rolled with ease up to 50 ft. long" (Dowlais great mill) | |
| odd lengths | "All iron of unusual lengths, or cut to exact lengths ... charged extra" | Percy p. 760 | no standard stock length is named | ||
| angle and tee | 1 1/4 x 1 1/4 x 1/4 and up to 10 united inches | Percy pp. 754-759 | extras by "united inches" | ||
| tyre bars | 3 1/2 to 8 cwt each, by weight | 178-406 | Percy pp. 754-757 | "From 3 1/2 to 4 cwt. each ... 7 and above" |
Rods: rivet, nail, wire
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| wire rod from Staffs mills | 3/16(?) to 1/4(?) in diameter, 40-50 ft long | 5-6 mm; 12-15 m | Fairbairn Iron p. 125 | "a strong wire [3/16] to [1/4] of an inch in diameter, and 40 to 50 feet in length" (fractions garbled) | |
| wire and small hoop mill | rods under 1/2 in, hoops under 1 in; rolls 4 1/2-5 in dia | Overman p. 358 | "rods less than half an inch, and hoops less than one inch wide" | ||
| small iron | under 1 in square or round, hoops under 2 in wide | Overman p. 354 | "wire, or small bar iron less than one inch square, or round, small hoops less than two inches wide" | ||
| nail rods, Welsh list | sold by wire gauge: "000 or 9 W.G.", "0000 or 9 x 10 W.G.", "9 x 11", "9 x 12" | Percy p. 758 | Staffs list: "Nail rods. No. 00 to 20 rod gauge" (p. 753) | ||
| rivet iron, Lowmoor | 9/16 and 1/2, 7/16 and 3/8, 5/16, 1/4, 3/16 in diameter; extras 20/, 40/, 60/, 80/, 100/ per ton | 14.3-4.8 mm | Percy p. 757 (PDF 777) | "Rivet Iron. 9/16 and 1/2 inch ... 20/ per ton extra; 7/16 and 3/8 ... 40/; 5/16 inch ... 60/; 1/4 ... 80/; 3/16 ... 100/". Its rounds list on the same page runs 9/16, 1/2, 7/16, 3/8, 5/16, 1/4, 3/16 at the same extras. The Staffs, Welsh and Scotch lists have a rivet-iron price row (p. 753) and no diameters. | |
| wire rod, extras | "will be coiled up without extra charge" | Percy p. 754 |
Hoop
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| puddle-train bar | see muck bar | ||||
| hoop widths, Staffs | 6 in down to 1/2 in, thinnest by width | Percy p. 754 (PDF 774) | "6 to 3 3/4 [read] inches not thinner than No. 14 W. G. ordinary gauge"; 3 1/2 to 2 1/4 [read] No. 15; 2 to 1 5/8 [read] No. 17; 1 1/2 to 1 3/8 [read] No. 18; 1 1/4 to 1 No. 19; 7/8 to 1/2 No. 20. "For each gauge thinner, 10/ per ton extra." Narrow widths 7/8, 3/4, 5/8, 1/2 carry 20/, 40/, 80/, 120/. The gauge numbers are clear; the inch fractions of the width bands are small type. | ||
| Newcastle | 7/8 in wide not thinner than No. 19, 3/4 and 5/8 in not thinner than No. 20 | Percy p. 755 | "7/8 inch wide not thinner than No. 19 W. G. ... 10/ per ton extra; 3/4 ... No. 20 ... 30/; 5/8 ... No. 20 ... 80/. For each gauge thinner ... 20/" (earlier digest read "1/2 inch ... No. 19") | ||
| Yorkshire, Scotch | Yorkshire 7/8 to 1/2 in by No. 20 W.G.; Scotch 7 in to 2 1/4 in not thinner than No. 15, then 17, 18, 19, 20 for 2, 1 1/2, 1 1/4, 7/8 and under | Percy pp. 756, 760 | "1/2 [sic] inch by 20 W. G. ... 20/ per ton extra"; "Hoops under 1 inch wide 20/ extra for each gauge under 20 W. G." | ||
| polished by hard rollers | 12-20 in long smooth rolls | Overman p. 354 | "Smooth hard rollers, twelve, frequently twenty inches long, which serve for polishing hoops" | ||
| cutting | portable hand shears at the rolls | Overman p. 378 |
Gauge-to-thickness: Rose p. 384 (below), Birmingham wire gauge: No. 14 0.083 in (2.11 mm), No. 15 0.072 (1.83), No. 17 0.058 (1.47), No. 18 0.049 (1.24), No. 19 0.042 (1.07), No. 20 0.035 in (0.89 mm). So a 6 to 3 3/4 in hoop is not thinner than 2.11 mm and the narrow hoops 0.89 mm; a 2 in hoop at No. 17 is 0.058 in thick and about 0.58 kg per metre (INFERRED, 0.282 lb/in3).
Sheet
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| sheet gauges listed | singles to No. 20 W.G. (0.035 in, 0.89 mm); doubles No. 21-24 (0.032-0.022 in, 0.81-0.56 mm); latten No. 25-27 (0.020-0.016 in), 28 (0.014), 29 (0.013) per Rose p. 384 | Percy pp. 753, 754, 758 | "Doubles, No. 21 to 24 W. G. ... 30/ per ton above singles. Latten, No. 25, 27 ... 60/" | ||
| Welsh limits | "Above 3 feet wide and under 11 W.G.", "8 ft. long, special agreement" | 0.9 m; 2.4 m | Percy p. 759 | ||
| mill bar for sheet | 4-6 in wide flat bars | 102-152 mm | Overman p. 366 | "These bars are from four to six inches wide" | |
| sheet rolls | 3 ft between the gudgeons, "seldom three and a half feet for thin sheet" | 0.9 m | Overman p. 366 | ||
| thin polished sheet | rolls 22-24 in long x 16-18 in dia; sheet over 20 in wide and 4-5 ft long "seldom made" | Overman p. 370 | "Highly polished sheet iron of larger size than twenty inches in width, and four or five feet in length, is seldom made." | ||
| sheet rolled in pairs | two or three sheets doubled through the rolls | Overman pp. 369-370 |
Boiler plate
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| standard plate, Staffs | up to 4 cwt, 4 ft wide, 24 sq ft, 15 ft long without extra | 1.22 m wide; 2.2 m2 | 203 | Wilson p. 91; Percy p. 755 | "The greatest width, without extra charge, is usually about 4 feet, and the length is arranged to keep the weight of the plate within 4 cwt." Percy extras: "24 feet superficial if under 4 cwt ... 15 [feet] long ... 4 [feet] wide ... 40/" |
| weight tiers, Staffs | above 4 to 5, 5 to 6, 6 to 6 1/2, 6 1/2 to 7 cwt per plate carry extras | 203-356 | Percy p. 755 | "Above 4 cwt. to 5 cwt. per plate ... 7" | |
| weight tiers, Yorkshire | from 3 cwt up to "Above 5 cwt" (300/ extra) | 152-254 | Percy pp. 757-758 | ||
| size tiers, Newcastle | 1/4 in (read) and thicker: 10/ for each 1/2 cwt above 4 cwt and 10/ for each 2 in wider than 4 ft; "more than 40 feet superficial, special agreement". Thinner than 1/4 to 3/16 in: 20/ for each 1 in wider than 4 ft, special agreement above 32 sq ft. 1/8 in (read): 20/ if 4 ft wide, special agreement above 4 ft wide or 28 sq ft | 40 sq ft = 3.7 m2; 32 = 3.0 m2; 28 = 2.6 m2 | Percy p. 755 (PDF 775) | "[1/4] inch and thicker, for each 1/2 cwt. above 4 cwt. ... 10/ per ton extra"; "Thinner than [1/4] to 3/16 inch, for each 1 inch wider than 4 feet 20/"; the plate-thickness fractions are small type, read at 500 dpi. Earlier digest read "1/2 in" for the first row; the glyph's denominator is 4 and the cwt glyph beside it is 1/2. | |
| length tiers, Welsh | 12 to 15 ft, 15 to 18, 18 to 21 ft long carry extras of 20/, 40/, 60/ | 3.7-6.4 m | Percy p. 759 | "12 [ft] long, and not exceeding 15 feet 20/ ... 18 [ft] ... 21 ... 60/" | |
| Scotch | "For each 1/2 cwt. above 4 cwt."; narrower than 12 in extra | Percy p. 760 | |||
| weight per square foot | 5 lb per 1/8 in | Courtney p. 95 | see weight rules | ||
| worked example | 6 ft x 3 ft x 3/8 in = 270 lb | 122 | Courtney p. 95 | "15 lbs. x 18 square feet = 270 lbs., or 2 cwt. 1 qr. 14 1/2 lbs." | |
| thickness range | tests quoted up to "not exceeding one inch" | Wilson p. 37 | |||
| slab for plate | 12-18 in long x 7-10 wide x 2-3 thick | 305-457 x 178-254 x 51-76 mm | Overman p. 369 | "The slab ... is generally from twelve to eighteen inches long, from seven to ten inches wide, and from two to three inches thick." | |
| lump and slab, Farnley | lump 12 in square x 4-5 in thick, piled; slab 2-4 ft long, 12-20 in broad | Percy p. 734 | "'lumps,' about 12 in. square and 4 in. or 5 in. thick ... a 'slab' ... from about 2 ft. to 4 ft. long, and from 12 in. to 20 in. broad" | ||
| rolled once, sheared square | "sheared square agreeably to order" | Percy p. 734 | |||
| plate rolls, Overman | 4 and even 5 ft long | 1.2-1.5 m | Overman p. 366 | "For the rolling of boiler-plate, we find rollers four and even five feet long in use." | |
| plate rolls, Fairbairn | "some of them for large plates are upwards of 6 feet long and 18 to 21 inches in diameter"; 28-30 rpm | 1.8 m; 457-533 mm | Fairbairn Iron p. 125; Mills II p. 258 | ||
| armour-plate mill, Atlas Works | rolls 32 in dia, 8 ft wide; 400 hp | 0.81 m; 2.4 m | Mills II p. 269 | "The rolls themselves are 32 in. in diameter and 8 ft. wide" | |
| largest plate rolled | armour plate 19 ft x nearly 4 ft x 12 in, 20 tons | 5.8 m x 1.2 m x 305 mm | 20300 | Fairbairn Iron p. 262 | "weighing 20 tons, 19 feet long, nearly 4 feet wide, and exactly 12 inches thick" |
| bridge and locomotive plates | "large plates ... of greatly increased weight" for front and tube plates | Fairbairn Iron p. 128 | |||
| plate rolls form | plain cylindrical, chilled, concave barrel | Truran p. 238; Fairbairn p. 124 |
Grades and how a boiler maker ordered
- Names: "Best Yorkshire", "Best Best", "Treble Best", "Best Scrap", "Crown"; "the use of the same brand by different makers, but for different qualities of plate ... has been productive of much misunderstanding" (Wilson pp. 32-34). "Best Best Best" of one house equals "Best Scrap" of another.
- Price list rows "Boiler plates" and "Best do.", and "Improved qualities of each make, as 'Best,' 'Best Best,' 'Best Best Best,' at an advancing rate of from 10s. to 80s. per ton extra" (Percy p. 753).
- Common grade named in Wilson p. 37: "Best Best" plates one inch thick and under, 21 tons per square inch tenacity, about 7 per cent elongation; best quality 24 tons, 12 per cent. Courtney p. 93 gives Yorkshire, best Staffordshire and ordinary iron as three factors for working strength.
- Ordering: by thickness, width, and weight per plate with extras; "The plates are also sometimes ordered sufficiently large to admit of a test-strip being cut off"; "Each plate should be gauged, or, still better, weighed" on delivery (Wilson pp. 36-37). Specifications "leave 2 in. to 4 in. from the nearest defect" at the edge (Wilson p. 36).
- Grain: boiler plate piled crosswise so the plate is equally strong each way (Truran pp. 230, 238); a cheaper way, two blooms hammered and rolled direct, "no higher than No. 2 iron" (Truran p. 230).
Slabs, skelp, rails
| figure | value | metric | kg | page | quote |
|---|---|---|---|---|---|
| tube skelp | the tube maker "must first obtain his rolled 'strip' from the ironmaster and convert the same into the 'skelp'" | Marks p. 122 | no strip width or length given | ||
| strip allowance | "a 12 in. strip equal to, say, 12 1/4 in." | 305 mm | Marks p. 13 | ||
| steam tube thickness | one gauge heavier than water, water one heavier than gas | Marks p. 123 | |||
| rails, US | 40-80 lb per yard, 60-65 common, 8 yd long | 20-40 kg/m | 225 | Overman p. 359 | "A rail eight yards long, which is the common size" |
| rails, colliery | 12-18 lb per yard | Percy p. 750 | |||
| rail rolls | 22 in minimum for shape rails | Overman p. 360 |
Rolls and shears (what sets the widest bar and plate)
| figure | value | metric | page | quote |
|---|---|---|---|---|
| puddling rolls | 18 in dia x 3 ft 6 in between bearings; 6 ft 6 in over necks | 457 mm x 1.07 m | Truran p. 224 | "generally 18 inches diameter by 3 feet 6 inches long between bearings" |
| large merchant train | roughing 6 ft 6 in x 22 in dia; finishing 3 ft 6 in x 18 in dia | Truran p. 231 | ||
| small merchant mills | 12 in dia, 110-130 rpm; guide rolls 8 in | Truran p. 234 | ||
| roughing, merchant (Fairbairn) | roughing 4-5 ft x 18 in; merchant 2 ft 6 in-3 ft x 18 in | Fairbairn Iron p. 125 | ||
| merchant (Overman) | rolls seldom over 3 ft; wire rolls 4 1/2-5 in dia; heavy iron 15-20 in dia | Overman pp. 354, 358 | ||
| plate rolls | 4-6 ft long (see boiler plate); 8 ft x 32 in for armour | above | ||
| cropping shears | for mill bars, about 3 tons, knives 12-16 in long | 305-406 mm | Truran p. 235 | "steel knives from 12 to 16 inches long" |
| cold shears | "capable of shearing cold iron 6 inches by 1 inch", 15-20 tons | Truran p. 235 | ||
| heaviest cam shears | bars "5 inches square are cut with the greatest facility" | Truran p. 237 | ||
| force shear | cast lever 7-12 ft; sheet cutters 16-20 in long; bar over 2 in square is sawn not sheared | Overman pp. 378-380 | ||
| plate shear | Thorneycroft's "cut upwards of 10 feet at one stroke" | 3 m | Fairbairn Iron p. 129 | OCR "cut upwards 2 of 10 feet at one stroke" |
| saws | steel or iron 3 ft 6 in-4 ft 6 in dia, 1300 rpm | Truran p. 235 |
Wire gauge (Birmingham)
Rose, Modern Machine-Shop Practice (1901), printed p. 384 (PDF 522), "Birmingham Wire Gauge" (the index's "387" for a gauge is the neighbouring rolled silver and gold gauge; the table is on 384).
| No. | in | mm | No. | in | mm |
|---|---|---|---|---|---|
| 0 | 0.340 | 8.64 | 11 | 0.120 | 3.05 |
| 1 | 0.300 | 7.62 | 12 | 0.109 | 2.77 |
| 2 | 0.284 | 7.21 | 13 | 0.095 | 2.41 |
| 3 | 0.259 | 6.58 | 14 | 0.083 | 2.11 |
| 4 | 0.238 | 6.05 | 15 | 0.072 | 1.83 |
| 5 | 0.220 | 5.59 | 16 | 0.065 | 1.65 |
| 6 | 0.203 | 5.16 | 17 | 0.058 | 1.47 |
| 7 | 0.180 | 4.57 | 18 | 0.049 | 1.24 |
| 8 | 0.165 | 4.19 | 19 | 0.042 | 1.07 |
| 9 | 0.148 | 3.76 | 20 | 0.035 | 0.89 |
| 10 | 0.134 | 3.40 | 21-24 | 0.032, 0.028, 0.025, 0.022 | 0.81-0.56 |
No. 25-28 are 0.020, 0.018, 0.016, 0.014 in (0.51-0.36 mm). Also 00 0.380, 000 0.425, 0000 0.454 in; 29-36 down to 0.004. Rose says "the progressive wire gauge numbers do not progress by a regular increment" and that the gauge is sometimes called Stubs'. The sizes are Holtzapffel's of 1843 ("determined by Holtzapffel in 1843"); the Birmingham gauge's "average wire is slightly larger than the designated gauge-number" from die wear (Rose p. 384).
Gaps
- No standard length for merchant bar, rod or hoop; only that small bars were made 20 to 50 ft and cut, and that odd lengths cost extra. No book here gives a typical shop length for flats.
- Birmingham wire gauge thickness table: filled, Rose p. 384 (see the Wire gauge section). Percy's "W. G." is taken as this gauge (INFERRED; the book does not say which).
- Rivet rod diameters: filled, Percy p. 757 (3/16 to 9/16 in). Wire-rod weights: not stated.
- Skelp strip width for a 2 in tube: no book read states it (Marks, Truran, Overman, Wilson, Fairbairn, Courtney searched for "skelp"; only Marks uses the word, pp. 11 and 122, without a width). Marks p. 11 (PDF 23) has an 1840s patent for flue tubes "from 1 1/2 in. to 2 in. diameter" of "iron of No. 14 of the wire gauge", 0.083 in. Strip width is INFERRED from the circumference: pi x (2 - 0.083) = 6.0 in for a butt weld, 6.5 in or a little more for a lap weld.
- Boiler-plate thickness range and a 15 x 16 style stock size: no source here names a standard thickness list; Wilson and Courtney work in eighths of an inch up to one inch.
- Hawkins (steel era), Spencer and Campbell were not read for these figures; Overman's plate sizes are American, 1851.
- Percy's puddle-bar thicknesses (p. 709, 3 in and 5 in bars) are unreadable in the scan even at 1000 dpi; no figure is given. The plate-thickness and hoop-width fractions on pp. 754-755 are read at 500 dpi and marked (read); the W.G. numbers and the rivet sizes on p. 757 are clear.
- Percy's boiler-plate list gives no standard thickness; it gives only the thickness breaks 1/4, 3/16 and 1/8 in (6.35, 4.76 and 3.18 mm) at which the extras change, and the widths and weights.
Typical size and weight per form
All INFERRED from the figures above unless a line says stated.
| form | mass | basis |
|---|---|---|
| puddled ball | 80 lb = 36 kg | stated, Percy p. 656 |
| bloom (5 x 18 in) | about 40 kg (60-100 lb stated) | Truran p. 219, Overman p. 334 |
| muck bar, 11 ft (4 x 3/4-1 in x 11 ft) | 59 kg | Fairbairn |
| muck bar cut for piling (4 x 7/8 in x 3 ft 6 in) | 19 kg | Truran p. 226 |
| large pile (3 ft 6 in x 7 x 8 in) | 203 kg (stated 4 cwt) | Truran p. 227 |
| small pile (18 x 3 x 2 3/4 in) | 19 kg | Truran p. 227 |
| merchant flat 3 x 1/2 in, 20 ft | 45 kg | Courtney p. 95 |
| merchant square 1 in, 20 ft | 30 kg | Courtney p. 95 |
| merchant round 1 1/2 in, 20 ft | 54 kg | Courtney p. 95 |
| wire rod 1/4 in, 45 ft | 3.4 kg | Courtney p. 95; Fairbairn p. 125 |
| hoop 2 in x No. 17 W.G. (0.058 in) | 0.58 kg per m (INFERRED) | Percy p. 754 (No. 17 for 2 to 1 5/8 in); Rose p. 384 |
| sheet, 4.5 ft x 20 in, No. 20 W.G. (0.035 in) | about 4.8 kg | Percy p. 753; Rose p. 384 |
| boiler plate 3/8 in, 4 ft x 6 ft | 15 lb/sq ft, 360 lb = 163 kg | Wilson p. 91; Percy p. 755 |
| boiler plate at the 4 cwt cap, 1/2 in (4 ft x 5.6 ft) | 203 kg | Wilson p. 91 |
| largest listed boiler plate (7 cwt, 4 ft wide) | 356 kg | Percy p. 755 |
| plate slab, 15 x 8.5 x 2.5 in | 40.8 kg | Overman p. 369 |
| skelp for 2 in tube, 6.0-6.5 in x 0.083 in (No. 14) x 12 ft | about 9-10 kg (INFERRED) | width inferred from the circumference, thickness Marks p. 11 |
| rail, 62 lb/yd, 8 yd | 225 kg | Overman p. 359 |
| widest plate roll | 8 ft wide between bearings (armour); 4-6 ft for boiler plate | Mills II p. 269; Overman p. 366 |