Rose, Modern Machine-Shop Practice - sizes of the period's machine tools
Books Modern Machine-Shop Practice
Source J. Rose, "Modern Machine-Shop Practice", Volume I (1901 printing of the 1887 work), modernmachinesho01roseuoft. Pages are the book's printed folios; each was read from the page head or the head of its neighbours, so a folio inside a run of plates can be one off. The note Rose, Modern Machine-Shop Practice (1901) holds processes, speeds and feeds; this page holds sizes only.
Read the lathe chapters (folios 119-221: sizes, headstocks, Sellers, Putnam, Ames, New Haven and Niles lathes, cone proportions, cylinder boring lathes), boring in the lathe (ch. XI, folios 274-295), shaping (ch. XVI, folios 389-402), planing (ch. XVII, folios 403-425) and drilling machines (ch. XVIII, folios 426-440). One plate was viewed as an image (Plate XCV, drilling machines).
Metric inches times 0.0254, rounded.
What the book gives
Rose is a descriptive book, not a trade catalogue. Sizes appear as a lathe's swing in a figure caption, as a few worked cone-pulley sums and, for the largest machines, as stated capacities. It gives no table of bed lengths, centre heights above the floor, headstock dimensions, planer tables or shaper tables for any machine of a small shop. Where the tables below are short, the book is silent, and the closing list marks every figure that is derived or has to come from another source.
Lathe
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| How a lathe is sized | swing and bed length; or height of centres and shears length; or swing and greatest length between centres | - | 120 | "First by the swing of the lathe and the total length of the bed ... The second is by the height of the centres (from the nearest corner of the bed) and the length of the shears." |
| Height of centres | half the swing; a 28-inch swing is a 14-inch-centres lathe | 28 in = 0.71 m swing, 0.36 m centres | 120 | "The height of the centres is obviously equal to half the swing of the lathe, hence, for example, a lathe of 28-inch swing is the same size as one of 14-inch centres." |
| Distance between centres | bed length less head and tailstock together | - | 120 | "the greatest length of work that can be held between the lathe centres, which is equal to the length of the bed less the lengths of the head and tailstock together." |
| Full swing is not usable over the rest | the slide rest or hand rest stands on the shears and cuts the swing on work between centres | - | 120 | "the full diameter of work that the lathe will swing on the face plate cannot be held between the centres on account of the height of the body of the hand rest or slide rest above the shears" |
| Small screw-cutting lathe, Fig. 484 | 12-inch | 0.30 m | 133 | "Fig. 484 represents a 12-inch lathe, cutting threads from 5 to 40 per inch" |
| Fig. 486 lathe | swing 16 inches; spindle hole about 1-1/8 inch (OCR reads "1 1'^") | 0.41 m; 0.03 m | 133 | "Fig. 486 has a swing of 16 inches and cuts threads from 3 to 24 per inch; the hole through the spindle being 1 1'^ inch." |
| Putnam engine lathe, Fig. 492 | 18-inch | 0.46 m | 133 | "Fig. 492 represents an 18-inch engine (or self-acting) lathe designed by ... S. W. Putnam" |
| Ames lathe, Fig. 505 | 28-inch swing | 0.71 m | 140 | "Fig. 505 represents a 28-inch swing lathe by the Ames Manufacturing Company" |
| Sellers self-acting lathe, Fig. 515: range of sizes | 12 to 48 inches swing on one design | 0.30 to 1.22 m | 143 | "made in various sizes from 12 inches up to 48 inches swing on the same general design" |
| Sellers gearing by size | 12 and 16-inch back-geared, six speeds; 20-inch back-geared, eight speeds; 25 to 48-inch triple-geared, fifteen speeds | - | 143 | "Lathes of 12 and 16 inches swing are back-geared, affording six changes of speed ... Lathes of 25 inches and up to 48 inches swing inclusive are triple-geared, affording fifteen changes of speed" |
| 44-inch swing lathe, Fig. 513 | 44-inch swing, extra slide rest bolted to the carriage side | 1.12 m | 143 | "Fig. 513 represents a 44-inch swing lathe, showing an extra and detachable slide rest" |
| Headstock of a 16-inch-class lathe, Figs. 516-517 | five steps on the cone, five more with the back gear, five more with an extra pinion on the face plate; the front bearing is "of large diameter" | - | 144 | "there are five changes of speed on the cone, five with the ordinary back-gear, and five additional ones obtained by means of an extra pinion" (the lathe's size is garbled in the scan) |
| English self-acting lathe, Fig. 527 | swings 12 inches over the shears; a gap piece under the live centre comes out to take more | 0.30 m | 147 | "capable of swinging work of 12 inches diameter over the top of the lathe shears, which are provided with a removable piece beneath the live centre" |
| Putnam pattern-maker's lathe, Fig. 528 | swings 50 inches in the gap; the upper shears slide to add 4 feet between centres; largest and smallest cone steps of iron, the middle ones of wood | 1.27 m; 1.22 m | 148 | "The lathe will swing work of 50 inches within the gap, and the upper shears will move sufficiently to take in 4 additional feet between the centres." |
| Ames 90-inch lathe, Fig. 537 | 90-inch swing | 2.29 m | 150 | "Fig. 537 represents a 90-inch swing lathe by the Ames Manufacturing Company" |
| New Haven lathe, Fig. 538 | 50-inch swing | 1.27 m | 150 | "Fig. 538 represents a 50-inch swing lathe by the New Haven" |
| Hand and screw lathe, Fig. 543 | 13-inch swing | 0.33 m | 151 | "Fig. 543 (Plate XL) represents a thirteen-inch swing hand and ..." |
| Niles 60-inch lathe, Plate XXII Fig. 1 | swing 60 inches over the ways, 46 inches over the carriage; five-step cone for a belt 4-1/2 inches wide; two sets of back gears, fifteen speeds; main spindle 10 inches at the front, bearing 15 inches long; carriage 68 inches long | 1.52 m; 1.17 m; 0.11 m belt; 0.25 m spindle; 0.38 m bearing; 1.73 m carriage | 153 | "The lathe swings sixty inches over the ways and forty-six inches over the carriage ... The main spindle is ten inches in diameter at the front end, and the bearing is fifteen inches long. ... The carriage is sixty-eight inches long" |
| Cone-step spread by size | the diameter difference between steps is 1 inch for a 12-inch swing, 2 inches for 30-inch, 3 inches for 5 feet or more | 0.025 m; 0.05 m; 0.08 m | 162 | "The variation in the diameter of the steps of a lathe cone varies from an inch for lathes of about 12-inch swing, up to 2 inches for lathes of about 30-inch swing, and 3 inches for lathes of 5 or more feet of swing." |
| Worked cone pair, six steps | centres of the two pulley shafts 60 inches apart; steps differ by about 2-1/2 inches; smallest step 5 inches; steps 17.50, 15.13, 12.70, 10.20, 7.63, 5.00 inches (not a particular lathe) | 0.44 m largest, 0.13 m smallest | 162-163 | "the centres of a pulley shafts to be 60 inches apart ... each cone is to have six steps, the smallest of which is to be of five inches diameter" |
| Four-step cone from the same sum | 12.50, 10.07, 7.57, 5.00 inches | 0.32 m largest | 163 | "each cone is to have four steps instead of six, the largest diameter will, in this case, equal 12-1/2 in." |
| Lathe bed width over the saddle, tailstock | not stated; bed and shears are described only as flat-topped or V | - | 143 | "The beds or shears are made with flat tops, the carriage being gibbed to the edges of the shears" |
Not found: bed length of any lathe, height of the centres above the floor, headstock or cone pulley diameter for a named small lathe (only the worked sum above and the Niles belt width), distance between centres of a named lathe.
Boring a cylinder (lathe and cylinder boring machine)
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Boring bar between lathe centres | the common small form is a solid bar carried on the lathe centres, the work fed along it by the carriage, the cutter fixed in a slot or in a head traversing the bar | - | 290 | "The common form of the smaller sizes of boring bar is that shown in Fig. 1127. A a being the bar, D D the lathe centres" |
| Bar length against work | a fixed-cutter bar must be at least twice the length of the work, because the work is wholly on one side of the cutter at the start and wholly on the other at the end | - | 290 | "the bar must be at least twice the length of the work, because the work is all on one side of the cutter at the commencement" |
| Bar made tapering | a bar used only on work needing no end facing tapers from the middle towards each end; the parallel part at one end takes the driving clamp | - | 290 | "the bar should be tapering from the middle towards each end, as shown in Fig. 1130" |
| Large bores | a bar that is too small for the bore carries a tool head fixed on it, or a head traversed by a feed screw inside or outside the bar | - | 289-290 | "a boring bar is best driven from both ends"; "to traverse the head carrying the tools along the bar necessitates a feed screw either within the bar or outside of it" |
| Centres of cast bars | cast iron bars have wrought plugs screwed into their ends for the centres | - | 290 | "to bore and tap the ends of such bars, and to screw in a wrought-iron or steel plug" |
| Heavy work stays fixed | "When work of considerable weight requires to be bored ... it is more convenient that it remain fixed upon a table, and that the boring tools rotate" | - | 218 | as quoted |
| Cylinder boring lathe, Fig. 738 | worm and worm-wheel on the cone shaft turn a bar with bearing in both heads; a table between two face plates carries the cylinder; the cutter head is fed along the bar by a screw in the bar | - | 219 | "Fig. 738 represents a cylinder boring lathe. D is the driving cone, on whose shaft is the worm W, driving the worm-wheel" |
| Sellers cylinder boring lathe, Fig. 739 | bar hollow, held in two heads; two face plates carry slide rests that face both cylinder ends while the bar bores | - | 219 | "The two face plates shown which drive the boring bar, also carry two slide rests which are used to face off the ends of cylinders while the boring bar is in operation" |
| Fig. 740 | a lathe for boring and facing cylinders together; the bar runs in two bearings, a slide rest at each end revolves with it | - | 220 | "specially designed for simultaneously boring and facing cylinders" |
| Floor boring machine, Fig. 1688 | two heads on a base plate; the horizontal bar sets at any height from 14 inches to 6 feet 4 inches above the base plate; eight speeds, four single and four double gear | 0.36 to 1.93 m | 433 | "may be set at any height from the base plate between the limits of 14 inches and 6 feet 4 inches" |
Not found: bar diameter, bed length or largest cylinder for any cylinder boring machine; no cylinder bore size is tied to a bar size anywhere in the volume.
Shaper
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Greatest stroke | a shaper's tool slide leaves its guides on the stroke, so its use is limited to about 18 inches, and in small machines to no more than 12 | 0.46 m; 0.30 m | 396 | "limited to work that does not require a greater tool stroke than about 18 inches, and in small machines not to exceed 12 inches." |
| Variable stroke, Fig. 1540 | stroke variable from 1/2 inch to 20 inches by tappets, with a uniform tool speed on both strokes | 0.01 to 0.51 m | 397 | "the range of stroke being variable from 1/2 inch to 20 inches" (the fraction is garbled to "\ inch" in the scan) |
| Quick return | the return stroke 40 per cent quicker than the cut | - | 396 | "the return stroke is 40 per cent. quicker than the cutting one" |
Not found: table size, ram height, throat or the height of the machine for any shaper; shapers appear only on plates (LXIX to LXXI) with no scale.
Planer
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Rotary planer, Fig. 1564 | cutter disk with twenty-four cutters on a circle of 36 inches; spindle bearing slide with 2 inches of motion for depth | 0.91 m; 0.05 m | 405 | "carries twenty-four cutters arranged in a circle of thirty-six inches in diameter" |
| Two-head planers, Fig. 1562 | two sliding heads, each independent, on the larger planers | - | 405 | "As the sizes of planing machines increase, they are given increased tool-carrying heads" |
| L-shaped bed, Fig. 1563 | one standard slides on an extension of the bed to suit the width of the work; used on the planers for marine engine parts | - | 405 | "the bed of the machine is L-shaped, the extension being to provide a slide to carry the right-hand standard" |
Not found: table width or length, stroke, height under the cross rail, or the size of any named planer, including the Sellers planer (Fig. 1565, p. 406).
Drilling machine
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Bickford drills, Plate XCIV | 20-inch drill with sliding head and counterbalanced spindle (Fig. 1, wheel feed; Fig. 2, lever feed); 24-inch back-geared power-feed drill (Fig. 3); a boilermaker's drill (Fig. 4); the table rises on a rack and pinion and swings round the column | 0.51 m; 0.61 m | 429 | "Fig. 1 is a 20-inch drill with a sliding head ... Fig. 3 represents the 24-inch back geared and power feed drill" (Rose does not say what the 20 and 24 measure; by the makers' practice it is the swing, twice the spindle-to-column distance, which the book does not state) |
| Slate's sensitive drill spindle, Fig. 1673 | one-inch steel spindle 19 inches long | 0.025 m; 0.48 m | 429 | "driven by a one-inch steel spindle 19 inches long" |
| Spindle travel by a stop | holes duplicated to any depth to 7-1/2 inches by the stop on the spindle sleeve | 0.19 m | 429 | "Holes may be duplicated to any depth to 7-1/2 inches by means of the stop H" |
| Elliott's drilling machine, Fig. 1672 | a small bench drill; the table revolves in an arm swung round the column; drill range printed as fractions the scan garbles | - | 429 | "Fig. 1672 represents Elliott's drilling machine for drills from ... inch to ... inch in diameter" |
| Plate XCV, Figs. 1676-1678 (image seen) | column machines on a cast base; the table rack-raised on the column; the cone with back gear at the column foot or back; no man in the picture | - | Plate XCV | Fig. 1676, Fig. 1677 (Prentice), Fig. 1678 (Sellers) |
| Giant drilling and milling machine | a large drilling and milling machine on a 30-foot bed with a 20 by 31 foot table, saddle with an 8-inch spindle | - | about 437-439 | "traverses 30 feet by hand and power, upon a bed C ... a work table D, 20 feet wide by 31 feet long" (not a small-shop machine) |
Not found: column height, spindle to column (throat), table size or spindle travel for any named drill, apart from the one-inch spindle and the 7-1/2 inch stop depth.
Figures with a man beside the machine
None found. The plates are catalogue cuts of the machine alone; the one plate viewed as an image (Plate XCV) has no man, and the captions read name no scale figure. The other plates were not viewed, so this covers the text and that plate, not every engraving.
Sizes in metres
Sourced figures first, then what Rose does not give.
Lathe (a small shop's: 12 to 28 inches swing)
- swing 12 in = 0.30 m; 16 in = 0.41 m; 28 in = 0.71 m (pp. 133, 140); centres at half the swing: 0.15, 0.20, 0.36 m (p. 120)
- cone steps spread 1 in (0.025 m) at 12-inch swing, 2 in (0.05 m) at 30-inch (p. 162); the worked six-step cone runs 5.00 to 17.50 in (0.13 to 0.44 m) on 60-inch shaft centres (p. 163, an example)
- the 16-inch class has five cone steps, five more with back gear (p. 144); the 12 and 16-inch Sellers have six speeds, back-geared (p. 143)
- the Niles 60-inch gives the proportions of a heavy one: spindle 10 in = swing / 6, front bearing 15 in, carriage 68 in, belt 4-1/2 in (p. 153); at the small swings these ratios are not stated
- not in Rose, needed from another source: bed length, between-centres length, centre height above the floor, headstock and cone outside diameters, bed width
Boring machine and boring in the lathe
- a bar between lathe centres, the work carried by the carriage; length at least twice the work; tapered from the middle if no facing is wanted; wrought centre plugs in a cast bar (p. 290)
- the cylinder boring lathe: bar driven by a worm wheel, a table between two face plates, a screw in the bar feeding the cutter head, slide rests on the face plates (pp. 219-220)
- the floor boring machine: bar height 14 in to 6 ft 4 in (0.36 to 1.93 m) above the base plate (p. 433)
- not in Rose: bar diameter, bed length, the largest cylinder
Planer
- rotary head: 24 cutters on a 36-inch circle (0.91 m) (p. 405)
- not in Rose: table width and length, stroke, height under the cross rail
Shaper
- stroke 12 in (0.30 m) in the small machine, 18 in (0.46 m) the common limit, 20 in (0.51 m) the longest named (pp. 396-397)
- not in Rose: table, ram height, throat
Drilling press
- spindle one inch (0.025 m) by 19 in (0.48 m) long on the sensitive drill (p. 429); stop depth to 7-1/2 in (0.19 m) (p. 429)
- the Bickford sizes 20 in (0.51 m) and 24 in (0.61 m), their measure unnamed in the book (p. 429)
- not in Rose: column height, throat, table size