Overman, The Manufacture of Iron (1851): blast machines and hot blast
Books The Manufacture of Iron
Source Frederick Overman, The Manufacture of Iron (Philadelphia, 1851), archive.org manufactureofiro00overrich.
Chapter VI "Blast machines" (pp. 393-427, read from p. 394) and Chapter VII
"Hot blast" (pp. 428-442). Page numbers are the printed folios; the PDF page is the printed page plus 6. OCR is rough in
the fan formula (p. 410) only.
Purpose sizes of the tub blower, the water-driven cast blowing cylinder and the beam blowing engine, and the volumes
of air they move. Facts are the book's; INFERRED marks my own arithmetic or reading. Metric is
converted here (1 ft = 0.3048 m, 1 in = 25.4 mm, 1 cu ft = 0.02832 m3, 1 psi = 6.895 kPa, 1 hp = 0.7457 kW); the book
gives none.
0. What the book does not give
- Air per minute for a tub or an iron cylinder: only the furnace's need (section 3) and the cylinder's bore, stroke and speed, from which the delivery is worked out here (INFERRED).
- Air per tuyere, per ton of iron or per furnace of a given height. The only per-ton figure is the stove surface per ton a week (section 5). The number of tuyeres is advice (cold blast few, hot blast as many as convenient), not a count.
- A bore, stroke or speed for any engine or waterwheel. There is no beam engine and no waterwheel size in these pages; the only drive figures are 12-16 hp for a tub machine (p. 396) and the efficiencies of section 4.
- Strokes a minute for an iron cylinder. The text gives a piston speed instead.
- Horsepower against air delivered. The text gives horsepower for a machine and efficiency as a percent, not hp per cubic foot; section 4 works one out (INFERRED).
- Furnace dimensions (a 33 ft stack is not described here; Overman's furnace chapters are outside this range).
1. Wooden bellows, tubs and cylinders
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Swedish (Widholm) bellows, strokes | 10-12 a minute, two bellows to one fire | - | 394 | "From ten to twelve strokes may be made in a minute, and two bellows are required for one fire." |
| Swedish bellows, size | 6-7 ft long, 30 in wide, piston motion 12 in | 1.83-2.13 m, 0.76 m, 0.30 m | 394 | "from six to seven feet long and thirty inches wide - the piston having a motion of twelve inches" |
| Tub machine, form | two round tubs, pistons worked from below by a beam and crank, dry receiver on top | - | 395 | "the machine with two round tubs or bellows - the piston working from below, and a dry receiver placed on the top of the tubs" |
| Tubs and receiver, bore and height | 4-4.5 ft wide, 4 ft high | 1.22-1.37 m, 1.22 m | 396 | "generally from four to four and a half feet wide, and four feet high, making the stroke of the piston three feet" |
| Tub stroke | 3 ft | 0.91 m | 396 | same |
| Tub strokes a minute | 8-10 | - | 396 | "From eight to ten strokes is generally the speed required to supply a charcoal furnace." |
| Receiver weight | piston in the receiver carries a box of iron or stones to counterbalance the blast | - | 396 | "a box h filled with iron or stones, to counterbalance the pressure of the blast, and to regulate it by playing up and down" |
| Receiver size | "very nearly those of one of the cylinders" | about 1.2-1.4 m wide | 411 | "Its dimensions should be very nearly those of one of the cylinders." |
| Valves | wood lined with leather | - | 396 | "The valves are made of wood, lined with leather." |
| Layout | beam below, tubs raised a few feet above ground | - | 396 | "The beam is generally laid below, and the tubs raised a few feet above, ground." |
| Tub wall | glued segments of dry pine or ash 1-1.5 in thick, fibre running round the tub | 25-38 mm | 396 | "composed of small segments of dry pine or ash, an inch or an inch and a half thick" |
| Tub tops and heads | 3 in thick | 76 mm | 397 | "The tops as well as the tubs are generally three inches thick." |
| Inside coating | glue and plumbago, or plumbago and soapstone wet; no fat or oil | - | 396-397 | "Fat or oil is an improper material with which to lubricate the surface of a wooden tub" |
| Piston packing | leather or hemp, or leather hose filled with horse hair or wool, in a turned groove | - | 403 | "packed with leather, or hemp, or by a mixture of both" |
| Pressure limit | 5/8 to 3/4 lb a square inch | 4.3-5.2 kPa | 426 | "In wooden cylinders, a pressure as high as five-eighths or three-quarters of a pound may be obtained" |
| Duty | one charcoal blast furnace, or 4-5 forge or Catalan fires | - | 396 | "It will work one blast furnace for charcoal, or from four to five forge, or Catalan fires." |
| Drive | water wheel or steam engine of 12-16 hp | 8.9-11.9 kW | 396 | "A steam-engine or waterwheel of from twelve to sixteen horse power is required" |
| Cost | $250-350 | - | 396 | "It can be erected at an expense of from $250 to $350." |
| Efficiency | 50-55 percent of the power applied | - | 426 | "of wooden cylinders, from 50 to 55" |
| Double-working tubs | in use, not preferred; a stopgap before iron cylinders | - | 396-397 | "The wooden tubs are but a temporary arrangement" |
| Air delivered | not stated; two tubs of 4-4.5 ft by 3 ft stroke at 8-10 strokes: 600-950 cu ft a minute if each tub delivers once a stroke, half that if "stroke" counts both tubs | 17-27 m3 a minute, or 8.5-13.6 | - | INFERRED: bore area x 3 ft x tubs x strokes (37.7 cu ft a tub stroke at 4 ft, 47.7 at 4.5 ft); the book's 1000-2000 need (section 3) fits the first reading, taking 10 percent dead-space loss off, only at the top of the range |
2. Cast-iron blowing cylinders, valves, receivers, pipes
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Form | two cylinders double stroke, beams and cylinders, pistons, pipes, valves, wheels and cranks all iron except wooden beams and pitmans | - | 398-399 | "the cylinders, pistons, pipes, valves, wheels, and cranks are all of iron, except the beams and pitmans, which are of wood" |
| Horizontal cylinder | piston rod through both heads, valves of sheet iron lined with leather hung vertically; suits a waterwheel with one or two cylinders | - | 399-400 | "The piston rod runs through both heads, to carry the weight of the piston" |
| Vertical cylinder | suits steam, piston balanced by the steam piston | - | 400 | "If the motive power is steam, the vertical position of the cylinder is decidedly preferable" |
| Water drive | two double-stroke cylinders need a receiver; three double-stroke cylinders blow steady with none | - | 400 | "Blast machines with three cylinders and double stroke ... produces a very steady blast, without a receiver" |
| One cylinder on a beam | blast cylinder on one end of a balance beam, steam cylinder on the other | - | 401 | "If the blast cylinder is on one end of a balance beam, and the steam cylinder on the other, the regularity of the blast is much greater." |
| Piston speed | 3 ft with a 4 ft cylinder; faster in smaller, slower in larger; faster with flywheel and crank | 0.91 m (unit of time not printed) | 401 | "In cylinders of four feet diameter, the piston can move with the speed of three feet; in smaller cylinders with greater, and in larger ones with less speed." |
| Strokes a minute | not stated; at 3 ft a second and the 6 ft stroke of the book's drawing, 30 single strokes a minute | 180 ft/min = 55 m/min | - | INFERRED: the book's "three feet" read as per second |
| Example cylinder | stroke 6 ft, piston head 4 in thick, cylinder 6 ft 6 in long (1 in clear each end), or 7 ft 6 in with valves in the metal | 1.83 m, 102 mm, 1.98 m, 2.29 m | 403 | "If the stroke of the piston is six feet, and the thickness of the piston head four inches, a cylinder six feet six inches long is required" |
| Valve area | one-twelfth of the piston surface; larger does no harm | 8.3 percent; for a 4 ft piston 1.05 sq ft = 0.097 m2 | 402 | "One-twelfth of the surface of the piston is sufficient for the passage of the blast; but no disadvantage results if the valves are larger." |
| Valve form | trap valves; semicircular with hinge on the diameter, or oblong with hinge on a long side; light, vertical | - | 402 | "Trap valves are the most practicable." |
| Dead space | loss at least 10 percent in the best machines, up to 25 | - | 402 | "the loss which this occasions amounts to at least ten per cent., and in some cylinders is as great as twenty-five per cent." |
| Piston packing, iron | wrought or steel hoop 1/4 in thick round the head, hemp or wool stuffed behind it | 6.4 mm | 403 | "A steel or wrought iron hoop, a quarter of an inch thick" |
| Efficiency | 60-65 percent of the power applied | - | 426 | "The effect of iron cylinder blast machines, compared with that of the motive power applied, is from 60 to 65 per cent." |
| Pressure | half a pound to a pound and more by the coal; a furnace taking 3/4 lb is held to it | 3.4-6.9 kPa | 411 | "one kind of charcoal will permit a pressure of but half a pound, while another kind requires a pressure of one pound and more" |
| Dry receiver | piston receiver, about a cylinder's size; "far from producing a uniform pressure", good for forges | - | 411 | "For forges, such receivers answer very well." |
| Air chamber, form | sheet-iron cylinder like a boiler, 4-8 ft diameter, flat or convex heads, 1/8 in sheet, safety valve and manhole | 1.22-2.44 m, 3.2 mm | 412-413 | "varies from four to eight feet in diameter" |
| Air chamber, size, two cylinders double stroke | 10 times the capacity of one blast cylinder | for the 4 ft by 6 ft cylinder (75 cu ft) 750 cu ft = 21 m3 | 413 | "sufficiently large if made of ten times the capacity of one of the blast cylinders" |
| Air chamber, size, one cylinder or two single stroke | 20-30 times the capacity of the cylinder | 1500-2260 cu ft = 43-64 m3 | 413 | "from twenty to thirty times the capacity of the cylinder is required" |
| Air chamber, size, three cylinders | none needed with large pipes | - | 412 | "the blast is generally so uniform that no receiver is needed" |
| Blast pipe, material | tin plate for forges; 1/8 in sheet iron or cast iron for furnaces | 3.2 mm | 413 | "pipes of sheet iron one-eighth of an inch thick, or of cast iron, are used" |
| Blast pipe, bore | at least 10 in per 1000 cu ft a minute, each further 1000 adding the same area; 4000 needs 20 in | 254 mm per 28.3 m3/min; 508 mm at 113 m3/min | 414 | "Where 1000 cubic feet of air per minute are to pass through one of medium length, the diameter should be at least ten inches. Each additional 1000 feet should have the same space, so that 4000 feet per minute require a diameter of twenty inches." |
| Blast pipe, length | beyond 100 ft the bore grows, "doubled with each additional 100 feet" | 30.5 m | 414 | "If the distance from the blast machine to the furnace is more than 100 feet, the diameter of the pipe is to be increased; and it may be doubled with each additional 100 feet" |
| Joints | cold blast: lead joint; hot blast: iron-filings cement (75 lb filings, 1 lb sal ammoniac, 1 oz sulphur, 2 lb clay); muffs 1/4 in clear all round | 6.4 mm | 414 | "the best joint we can use is the leaden one" |
| Pipe support | on rollers (short bar or 2 in cast pipes), sliding muffs or stuffing boxes in long hot runs; elbows turned in a large circle | 51 mm | 414-415 | "rested upon rollers" |
| Pipe route | below the hearth bottom stone is preferred, free to move | - | 415 | "The latter plan is preferable" |
| Machine site | cool, dry, dust-free, near but not hard against the furnace | - | 426 | "A cool, dry place, to which no moisture has access, and which is free from sand and dust" |
| Fan (alternative) | cast sides, sheet-iron wings; width 6-20 in, diameter seldom over 3 ft, 700-1800 rev/min, belt pulley 4-6 in, four wings | 152-508 mm, 0.91 m | 407-408 | "The diameter of a fan is seldom more than three feet" |
| Fan pressure | seldom a quarter pound; blows a Catalan or German forge | 1.7 kPa | 426 | "The best fans seldom produce a pressure of a quarter of a pound" |
| Screw (Cagniardelle) | water-sealed rotating cylinder 2-10 ft; 90-95 percent efficient; Overman's favourite in principle, wet air | 0.61-3.05 m | 406-407, 426 | "its effect amounts to from 90 to 95 per cent. of the power applied" |
3. What each furnace takes
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Charcoal forge | 400-500 cu ft a minute | 11-14 m3/min | 401 | "A charcoal forge requires from 400 to 500 cubic feet per minute" |
| Finery | 800-1000 | 23-28 m3/min | 401 | "a finery from 800 to 1000" |
| Charcoal blast furnace (cold blast) | 1000-2000 | 28-57 m3/min = 0.47-0.94 m3/s | 401 | "a charcoal furnace from 1000 to 2000" |
| Anthracite or coke furnace | 3000-5000 | 85-142 m3/min = 1.4-2.4 m3/s | 401 | "an anthracite or coke furnace from 3000 to 5000" |
| Hot-blast furnaces | no separate volume; hot blast gives "nearly twice the quantity of iron" in a given time on anthracite and coke, 50 percent more on hard charcoal | - | 442 | "nearly twice the quantity of iron within a given time that we should realize by cold blast" |
| Pressure, charcoal | 1/2-1 lb and more by the coal; wooden tubs reach 5/8-3/4 lb | 3.4-6.9 kPa | 411, 426 | see sections 1-2 |
| Pressure, coke, anthracite, hard charcoal | more than wooden cylinders give; "cannot be carried on to advantage without iron bellows". No figure given | - | 426 | "Hard, sound charcoal, anthracite, and coke require a greater degree of pressure." |
| Pressure gauge reading | mercury tube 12 in for a charcoal furnace, 24 in for anthracite; inches of rise read nearly as lb a square inch | 305 mm, 610 mm | 424-425 | "the length of which, for a charcoal furnace, should be twelve inches, and for an anthracite furnace, twenty-four inches" |
| Pressure and heat | strong dense blast replaces hot blast | - | 427 | "pressure is an equivalent for hot blast" |
| Nozzle bore | 1 in forge; 1.5-2.5 in charcoal furnace; 3-4 in coke and anthracite; hot blast larger than cold | 25 mm; 38-64 mm; 76-102 mm | 416 | "nozzles of one inch diameter at charcoal forges; from one and a half inch to two and a half inches at charcoal furnaces; and from three to four inches diameter at coke and anthracite furnaces" |
| Nozzle length and shape | tapered tube 1-4 ft long; cylindrical nose as long as the opening for hard coal; short | 0.30-1.22 m | 415, 417 | "a three inch nozzle requires a cylindrical nose three inches long" |
| Nozzle sets pressure | with a limited machine the opening fixes the pressure | - | 416 | "it is the opening of the nozzle which determines the pressure of the blast" |
| Tuyere bore, narrowest | 2 in charcoal furnace, 4-4.5 in anthracite; inside seldom over 4 in; never wider than the nozzle | 51 mm; 102-114 mm | 419-420, 417 | "may be two inches wide at the narrowest point, as at charcoal furnaces, or from four to four and a half inches, as is the case at anthracite furnaces" |
| Tuyere length | water tuyere 10-20 in | 254-508 mm | 420 | "Water tuyeres are generally from ten to twenty inches long" |
| Tuyere water pipes | lead, 3/4 in bore, seldom 1 in; forge tuyere 1/2 in | 19 mm, 25 mm; 12.7 mm | 419-420 | "of lead, three-fourths of an inch, seldom one inch, bore" |
| Tuyere count | cold blast few; hot blast as many as convenient, on both sides of the hearth | - | 422-423 | "in using cold blast, we should employ as few, and in using hot blast, as many, tuyeres as possible" |
| Fuel saved by hot blast | anthracite and coke 30-60 percent; hard charcoal 20 percent; soft charcoal little | - | 442 | "The amount of fuel saved, in anthracite and coke furnaces, varies from thirty to sixty per cent." |
4. Power to blow
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Tub machine for one charcoal furnace | 12-16 hp | 8.9-11.9 kW | 396 | see section 1 |
| Efficiency of machine | iron cylinder 60-65 percent; wooden cylinder 50-55; smith's or wooden bellows 30-40; other "fancy" machines 15-20; screw 90-95 | - | 426 | "of the blacksmith's bellows, and wooden bellows of similar construction, from 30 to 40; and of all the fancy machines scarcely from 15 to 20 per cent." |
| Surplus of power | the manager must have pressure "at all times perfectly within the power", with "a surplus of power" | - | 426 | "a well-constructed machine, and a surplus of power, are indispensable" |
| Drive choice | waterwheel only where there is no waste heat; steam preferred at blast furnaces; wheel dearer than engine | - | 400 | "The expense of erecting a steam-engine will be found less, in most cases, than that incurred in the erection of a waterwheel." |
| Crank irregularity | a single cylinder on a crank blows unevenly and needs a large receiver | - | 400 | "a great irregularity in the blast ensues, and a comparatively large receiver is therefore required" |
| Air power, worked | pressure x volume: 1000 cu ft a minute at 0.75 lb is 3.3 hp, 2000 is 6.5 hp; at 1 lb 4.4 and 8.7 hp; divided by 0.55-0.65 efficiency gives 5-8 hp (1000) and 10-16 hp (2000) at the shaft | 2.5-4.9 kW; 7.5-12 kW | - | INFERRED from psi x 144 x cu ft / 33,000; the tub machine's 12-16 hp matches the 2000-cu-ft end |
5. Hot-blast stoves
| Figure | Value | Metric | Page | Quote |
|---|---|---|---|---|
| Pipe stuff | grey cast iron; wrought oxidizes, pipes bent horizontal sag under their own weight, so vertical pipes | - | 428 | "Air-heating pipes should be made of gray cast iron" |
| Round-pipe stove (Fig. 143-144) | round pipes 3 in inside; two lower straight pipes 15 in or less, 4 ft apart, so round pipes about 5 ft across | 76 mm; 381 mm; 1.22 m; 1.52 m | 429-430 | "The diameter of the round pipes is generally three inches inside, and that of the two straight and lower pipes, fifteen inches or less" |
| Straight-pipe stove (Fig. 145) | straight pipes almost vertical joined at the top by a curved pipe, 6-8 ft long at large furnaces, 5 in inside, metal 1 in thick | 1.83-2.44 m; 127 mm; 25 mm | 431 | "frequently from six to eight feet in length at large furnaces; diameter inside five inches; metal one inch thick" |
| Pipe count | small charcoal furnace: 5 ft long, 8 pipes; large anthracite or coke furnace: 30 and more | 1.52 m | 431 | "an apparatus five feet long, consisting of eight pipes, is sufficient" |
| Heating surface | 3-4 ft square exposed to the flame heats air for one ton of iron a week | printed "feet square", read either as 3-4 ft on a side (0.9-1.2 m, 0.84-1.5 m2) or 3-4 sq ft (0.28-0.37 m2) | 431-432 | "a surface from three to four feet square is, when exposed to the heating flame, large enough to heat an amount of air sufficient for one ton of iron per week" |
| Flame passage | 1.5-2 in between pipes; vertical pipes close together | 38-51 mm | 430 | "does not require more than one and a half or two inches" |
| Flame source | furnace top gas, or waste heat after the boilers; fire-brick lined; heavy brickwork steadies the blast heat | - | 430, 432, 441-442 | "the air-heating stove at the end of the steam boilers" |
| Flame entry | at the end the hot blast leaves | - | 430 | "the grate, or the entrance of the flame, should be put on that end of the apparatus from which the hot blast is let off" |
| Blast temperature | about 500 F, lead's melting point, is the limit of advantage; higher for anthracite, much lower for charcoal | 260 C | 435 | "The highest heat ... which results in advantage, has been found to be about 500 deg, or, the melting point of lead." |
| Gauge metals | lead melts 470 F, tin 380 F, tinner's solder 410 F, type metal 350 F; mercury boils 660 F | 243, 193, 210, 177, 349 C | 433 | "Pure lead melts at 470 deg; mercury boils at 660 deg; tin melts at 380 deg" |
| Saving from air temperature | 400 F air saves 10 percent in a furnace at 4000 F, 20 percent at 2000 F | 204 C; 2200 C, 1090 C | 435-436 | "in a furnace heated to 4000 deg, to which air of 400 deg is applied, ten per cent. of fuel will be saved" |
| Hot-air pipe | direct cold-blast bypass kept; pipe from stove packed in sand or loam; sheet-iron cap and nozzle; 3/4 in poker rod through a stoppered hole to the tuyere | 19 mm | 432-433 | "It is advisable to have a direct communication between the tuyere and the blast machine" |
| Hot nozzles | all metal, no leather bag; no movable nozzle needed | - | 416 | "Where hot blast is employed, leather cannot be put into the conducting pipe." |
| Pressure gauge on hot blast | 1 in bore lead or iron pipe through a cold water trough before the mercury | 25 mm | 425 | "the hot air will thus be cooled before it reaches the mercury" |
6. Closing list
For a charcoal furnace of about 33 ft, cold blast, 1000-2000 cu ft (28-57 m3, 0.47-0.94 m3/s) a minute at 1/2 to 1 lb (3.4-6.9 kPa). Overman's text does not tie the 33 ft to any of these; the furnace is the one the "charcoal furnace" range describes.
Tub blower (wooden, p. 395-396, 426):
- two round tubs and a dry receiver on top, each 4-4.5 ft (1.22-1.37 m) wide and 4 ft (1.22 m) high, glued staves of ash or pine 1-1.5 in (25-38 mm) thick, tops 3 in (76 mm); piston stroke 3 ft (0.91 m), pistons worked from below by a beam laid under the floor and a crank, tubs raised a few feet; valves wood lined with leather.
- 8-10 strokes a minute; the receiver piston carries a box of iron or stones; pressure limit 5/8-3/4 lb (4.3-5.2 kPa); 12-16 hp (8.9-11.9 kW) from a waterwheel or engine; 50-55 percent efficient; one charcoal furnace or 4-5 forge fires.
- delivery per minute is not given: INFERRED 600-950 cu ft (17-27 m3) for the two tubs at one delivery per tub stroke, 300-480 if the book's "stroke" counts both; open which reading is the book's.
- pipe 10 in (254 mm) per 1000 cu ft; nozzle 1.5-2.5 in (38-64 mm), water tuyere 2 in (51 mm) narrowest, 10-20 in (254-508 mm) long, lead water pipes 3/4 in (19 mm).
Water-driven cast blowing cylinder (p. 398-403, 411-413):
- horizontal for one or two cylinders on a wheel (piston rod through both heads, vertical sheet-iron valves lined with leather); two double-stroke cylinders cranked at right angles with a receiver, or three double-stroke with none.
- bore about 4 ft (1.22 m), stroke about 6 ft (1.83 m) (the book's drawing example, p. 403), piston 3 ft (0.91 m) a second at 4 ft bore (p. 401), faster in smaller bores; piston head 4 in (102 mm) thick with a 1/4 in (6.4 mm) hoop and hemp packing; clearance 1 in (25 mm) each end; dead-space loss 10-25 percent.
- valves total 1/12 of the piston area (1.05 sq ft, 0.097 m2 at 4 ft bore), light, vertical.
- air chamber 4-8 ft (1.22-2.44 m) diameter, 1/8 in (3.2 mm) sheet, safety valve and manhole, 10 times one cylinder's volume for two double-stroke cylinders (about 750 cu ft, 21 m3 at 4 by 6 ft), 20-30 times for one (1500-2260 cu ft, 43-64 m3).
- delivery INFERRED about 2260 cu ft (64 m3) a minute at 30 single strokes, 1700-2000 cu ft (48-57 m3) after dead space; efficiency 60-65 percent. Overman himself advises steam over water for a furnace (p. 400).
Beam blowing engine (p. 400-401, 426): Overman gives no engine size. What he does give: one blast cylinder on one end of the balance beam, the steam cylinder on the other (p. 401); vertical cylinders suit steam, piston weight balanced by the steam piston (p. 400); a large receiver of 20-30 times the cylinder instead of a second cylinder (p. 413); the blast cylinder kept away from the steam cylinder and boilers so no steam or heat reaches it (p. 401); 60-65 percent efficiency (p. 426). Power: INFERRED 5-8 hp at the shaft for 1000 cu ft and 10-16 hp for 2000 at 0.75-1 lb. The book gives no bore, stroke or strokes for the steam end.
Hot blast (p. 429-436, 442): stove of 8 pipes 5 ft long for a small charcoal furnace; 3-4 ft square of surface per ton a week; blast to about 500 F (260 C), less for charcoal; 20 percent fuel saved on hard charcoal, 50 percent more iron; nozzles larger than cold blast, all metal.