What a rolling stand is made of, part by part

Books The Manufacture of Iron, Treatise on Mills and Millwork, Part II, Metallurgy: Iron and Steel

Covers three books, only for the rolling stand:

  • Overman, The Manufacture of Iron (1850/51), Printed folio = PDF page less 6. Read pp. 344-374 (roughing rollers, merchant mill, heavy bar and rail rollers, sheet and boiler plate, polished sheet; PDF 350-380). Figures are read from the text that describes them; no plate was viewed.
  • Fairbairn, Mills and Millwork Part II (1863), Offset PDF less 42 from p. 184 on (p. 257 is PDF 299, p. 269 is PDF 311); less 26 for pp. 33-126 (p. 81 is PDF 107, p. 93 is PDF 119). Read pp. 257-260, 269-270 (iron mills, armour plate), p. 81 (couplings) and pp. 93-94 (plummer-blocks).
  • Percy, Iron and Steel (1864), no text layer; the OCR is poor in places and carries few folio marks, so Percy pages are +/- 1. Read pp. 707-709 (Brown's shingling machine, puddle rolls), p. 722 (rail mill), p. 727 (tin-plate rolls). Not repeated: Fairbairn pp. 258-259 on casting rolls (loam mould in a pit, bar rolls in chill, plate rolls of the most tenacious metal, Staffordshire wire rolls cast steel) is in the note on Fairbairn's books. Purpose each part's metal, form and finish, as the books give it. Overman describes the American (Pennsylvania) practice of c. 1850, Fairbairn and Percy the British.

Answer to the three questions

  • Rolls entirely cast iron: that is what all three books say. No book wraps, sleeves or faces a roll in wrought iron. The only variants are chill-cast (hard, bar and sheet-polish rolls) and cast steel (Staffordshire wire).
  • Wrought iron for tables: not supported. The aprons and guides are cast iron; wrought iron appears only as the scraper edges, the guard wedges and (Overman p. 366-368) housings of heavy sheet mills.
  • Screws: wrought iron in a brass box in the cast top, turned by a wrench (lever); detail in the table.

Table

PartMaterial and formFinishPagesQuote (short)
1a Housings (standards)Cast iron frame, two pillars, e.g. "ten by twelve inches square in the pillars" for heavy bar; 5 ft tall; width between pillars = roll diameter plus 1 inCast; Overman gives no machiningOverman pp. 349-350"The housing a is a heavy frame of cast iron"
1a' Housings, heavy sheetWrought iron for thin polished sheet, cast iron too weak "unless very heavy"; Fig. 121 wrought pillars cast into the bottom plate, each with its own screw and nutForged round pillarsOverman pp. 366-368"In this case, wrought iron standards are preferable"
1b Caps (housing top)Merchant mill: cap cast as a separate piece, "screwed on by bolts", so rolls lift out by crane. Roughing/bar: cast iron top carries the screw brass boxCast; boltedOverman pp. 350, 354"the cap a is cast as a separate piece, and screwed on by bolts"
1c Bed or sole plateCast iron bed plate; housings screwed to it; plate bolted to foundation by separate screws; two prismatic ribs on the plate fit notches in the housings. Foundation stone or brick 8-9 ft deep (timber for temporary works). Fairbairn: engine and rolls "fixed upon a large bed plate"Cast; ribs and notches fittedOverman pp. 345, 352; Fairbairn p. 258"screwing the housings to the bed-plate ... two projecting, prismatic ribs"
1d Tie of the housingsNot a tie rod. Screw bolts "steady the housings, and secure the close fitting of the boxes"; plate rests on the sill; cast iron frame between housings carries the guides (merchant mill)BoltedOverman pp. 351, 356"The screw bolts i, i serve to steady the housings"
2a Screws (screw-down)Wrought iron, "generally four and a half inches in diameter", square thread 1/4 to 3/8 in, one turn = 1/2 to 3/4 in. Two screws, one per housingThreaded; no further finish statedOverman p. 350"The wrought iron screw b is generally four and a half inches in diameter"
2b Screw nutBrass box, hexagonal and slightly tapered, driven "very tight into the cast iron top". Fig. 109 variant: nuts rest on a wrought iron plate fitted on a collar of the screw neckFitted into the housing topOverman pp. 350, 352"moves in a brass box, which is hexagonal and a little tapered"
2c Turning the screwA wrench (lever) on each screw; "the wrenches on the top screws form a cross" so one handle always faces the men before the rollers. Armour mill: a screw through compound levers (Fairbairn); Brown's machine: pinions on the screws and a toothed wheel with weighted lever (Percy). Worm or wheel: not shown for a mill standWrench forgedOverman pp. 350, 367; Fairbairn pp. 269-270; Percy pp. 707-708"The wrench g serves to lower and raise the top roller"
2d Holding the top roll upFig. 107: the screw presses the cap and the top roll is loose in the housing. Fig. 109, preferred: the nut-plate rides the screw collar so the top roll "always closely fitted in the plummer blocks". Counterweights "applied either below or above the rollers" keep the rolls apart where the top roll moves on its own pinions. Hangers and springs: not mentionedFittedOverman pp. 350, 352, 367"the first is generally balanced by counter weights"
3a Chocks (plummer blocks)Cast iron box carrying the neck; the cap and its lower part slide "on both sides in the housing, either in triangular or square grooves". Merchant mill: boxes in a square groove, screws behind them hold the roll lengthwise. Three-high: the middle and top blocks movable. Fairbairn's shaft plummer block: cast pedestal, cap, brass stepsCast, groove fittedOverman pp. 350, 355, 357; Fairbairn pp. 93-94"slides on both sides in the housing, either in triangular or square grooves"
3b Brasses and safety capThe top chock under the screw is the "safety-cap", cast iron, "calculated to break before any other part"; its boxes are brass, "frequently lined with hard lead or type metal"Cast; brass fittedOverman p. 350"The cap d is of cast iron, lined with brass boxes"
4a Aprons (tables, fore plates)Cast iron plate "filling the space between the housings, and joining the bottom roller, so as to form a bench"; a second, lower apron behind for roughing. Heavy sheet: broader apron with small friction rollers on the work sideCast; edge fitted to the rollOverman pp. 350, 368"h is a cast iron plate, called an apron"
4b Rest bar and scrapers (strippers)Flat and rail rolls: "a square bar of wrought or cast iron" carries wedge-shaped wrought iron scrapers loose in the grooves. Roughing apron: scrapers cast on, or better screwed on, the plate then wrought ironForged wedgesOverman pp. 350-351"wrought iron scrapers, having the form of wedges"
4c GuardsA second set below the scrapers: wrought iron wedges "in a strong cast iron grooved bar"ForgedOverman pp. 351-352"guards ... are wrought iron wedges"
4d GuidesRound and square bar: a frame fitted between the housings, with cast iron guides sliding in it, held "by wedges or screws"; guides and frame cast iron. Hoop polisher: iron frame turning in necks on the housings, crank at one endCastOverman pp. 356-357"The guides and frame are made of cast iron"
5a Spindles (junction shafts)Cast iron, "two or two and a half feet in length"; section not plain square, a cross-shaped section (Fig. 111), 3-4 in. for wire, 5-6 merchant, 8-10 plate, 10-12 polished sheetCastOverman pp. 346, 353"cast iron spindles two or two and a half feet in length"
5b Coupling boxes (wobblers)Cast iron, "frequently cast in one piece with the rod"; boxes on the spindles "kept in their places by four wooden sticks" filling the corners, bound by leather straps. Disengaging cam box: a box sliding on the shaft by an iron forkCastOverman pp. 346, 352-353"four wooden sticks ... leather straps"
5c Pinion housingTwo "standards" carrying two cogwheels of the roll diameter; "the upper part above the sill is all made of cast iron"; sheet mills often omit pinionsCastOverman pp. 345, 366-367; Fairbairn p. 257"At b are two standards, carrying two cogwheels"
6a Roll metalCast iron "of good metal, strong, but not very gray"; rail rolls with collars not under 2 in. Puddle rolls "strong cast-iron, such as mottled". Hard or chilled rolls for polished sheet; cold-chilled rolls "highly polished with emery and oil" for tin-plateCast, chill for hard rollsOverman pp. 362, 368; Percy pp. 708, 727"Rollers for flat iron must generally be good castings"
6b Necks and wobblersPlate rolls: bearings "enlarged, or turned to the shape" (Fairbairn); sheet rolls measured "between the gudgeons". Wobbler form: not describedTurnedFairbairn p. 259; Overman p. 366"bearings or neck should be enlarged"
6c Turning after castingGrooves "turned on" (Percy, puddle and rail rolls); roughing grooves roughened with a chisel; bottom roll groove corners left standing (not cut square). Fairbairn turns shaft couplings in the latheTurned in a lathePercy pp. 709, 722; Overman p. 349; Fairbairn p. 81"series of flat grooves turned on"

What none of the three books covers

  • The roll lathe: no book describes the lathe, its tool or its drive for turning rolls; only that grooves are "turned on".
  • Whether a roll is wrought-iron faced or sleeved: not mentioned anywhere read.
  • Springs holding the top roll up, and hangers: not mentioned; counterweights only (Overman p. 367).
  • A worm or worm wheel on a roll screw: not shown (Percy's pinions and toothed wheel are on a shingling machine).
  • Wrought iron tables, deck plates or rails: none; aprons are cast iron.
  • Roll neck diameter to roll diameter, and the form of the wobbler end: no figures read.
  • Housing cap and chock tie bars or cross-stays above the caps: not described.
  • Screw nut and cap dimensions, and any mill with a pit-sunk housing: not covered.
  • Plates (figures) were not viewed; forms are from the text.