Sellers and Niles, machine-tool catalogues: sizes of lathes, cylinder borers, planers, shapers and drills, 1873-1895

Books A Treatise on Machine Tools, Machine Tools for Working Metal, Catalogue

Sources

  • ATreatiseOnMachineTools1877 - William Sellers & Co., "A Treatise on Machine Tools, Etc.", fourth edition, Philadelphia 1877 (with the report of the 1876 Centennial judges).. Google scan, noisy OCR; read only where it adds to the 1895 catalogue.
  • WilliamSellersAndCoMachineToolsCatalogue1895 - William Sellers & Co., "Illustrated Catalogue and General Description of Machine Tools for Working Metal", 1895.. Clean text, tables checked against page images.
  • cu31924063726289 - Niles Tool Works, Hamilton, Ohio, "Catalogue of the Niles Tool Works", 1891.. Source of the cylinder borers for stationary engines.

The 1891 and 1895 catalogues are later than the 1873-1877 Sellers treatise; the Sellers lathe table is the same family as the 1873-1877 one. Earlier British catalogues (Whitworth, Nasmyth, Fairbairn) were searched for on archive.org and not found as scans; Shelley's "Workshop Appliances" (1873) is a gauging and measuring book and was not downloaded. See Gaps.

Page convention p is the PDF page. Printed folio is Sellers 1895 p - 8 and Niles p - 14; a printed folio is given in brackets where it helps. Metric inches times 0.0254, feet times 0.3048, rounded. Inch marks inside quotes are written in; a fraction the OCR lost is read from the page image, and where the image does not settle it the row says so. INFERRED marks my arithmetic or reading, never a source statement.

Companion note: the Rose sizes note (Rose, swings, centres half the swing, cylinder boring lathes in outline).

Engine lathes

Sellers sizes a lathe by the diameter that swings clear of the bed; the table gives the swing over the rest, the shortest bed and the length between centres. Niles gives swing over the ways and over the carriage.

FigureValueMetricPageQuote
Sellers 48 in lathe, swing48 in over the bed, about 38 in over the rest (fraction not legible)1.22 m; 0.97 mSellers 1895 p136 (128)"Maximum swing over bed, 48" " (p121 lathe plate); table row "48" ... "17' 03" "
Sellers 48 in lathe, between centres8 ft 10 in2.69 mSellers 1895 p136 (128)table column "Distance between Centres", row 48 in: "8' 10" "
Sellers 48 in lathe, bed17 ft 0 3/4 in total length of the shortest bed, four girts beyond the live head5.20 mSellers 1895 p136 (128)column "Total Length of Bed", row 48 in: "17' 03" "
Sellers 36 in latheover rest 28 5/8 in; between centres 6 ft 7 1/2 in; bed 12 ft 10 1/2 in0.73 m; 2.02 m; 3.92 mSellers 1895 p136 (128)row 36 in: "28
Sellers 42 in latheover rest 34 1/4 in; between centres 8 ft 6 3/4 in; bed 14 ft 11 3/4 in0.87 m; 2.61 m; 4.57 mSellers 1895 p136 (128)row 42 in, read from the page image
Sellers 60 and 72 in lathes60 in: over rest 49 in, between centres 9 ft 1 1/4 in, bed 17 ft 3 1/8 in, six girts. 72 in: over rest 57 1/2 in, between centres 10 ft 1/2 in, bed 19 ft 9 3/4 in, eight girts1.24 m, 2.77 m, 5.26 m; 1.46 m, 3.06 m, 6.04 mSellers 1895 p136 (128)"Will swing over bed, 60" ; will swing over slide-rest, 49"." (p123)
Centre height over the shear, roll lathe31 in and a fraction (OCR "31}") for a 60 in roll latheabout 0.80 mSellers 1895 p139"Height from centre of spindle to top of lathe shear, 31}''."
Centre height, 54 in wheel lathe27 in above the top of the bed; swings 49 in over the saddle0.69 mSellers 1895 p149"Height of centre above top of bed, 27"."
Centre height, pulley lathe20 in from centre to top of bed (36 in pulley lathe)0.51 mSellers 1895 p152"Height from centre to top of bed, 20"."
Centre height, axle lathe8 in above the bed0.20 mSellers 1895 p141"Height of centres above bed, 8"."
Centre height equals half the swingthe swing over the bed is twice the height of the centres above the shear-Rose digest p120see the Rose page; the Sellers rows above agree (60 in swing, 31 in; 54 in wheel lathe, 27 in)
Cone and headstock36 in: spindle 5 in, front bearing 7 in, carriage 48 in. 48 in: spindle 6 1/4 in, front bearing 9 in. 60 in: front bearing 10 in by 15 in5 in; 6.25 inNiles p87, p88, p89"The spindle is 5 inches diameter, and front bearing is 7 inches long."; "The spindle is 6}4 inches in diameter, with a front bearing 9 inches long."
Niles 48 in latheswings 48 in over the ways, 36 in over the carriage; bed 16 ft 3 in turns 8 ft between centres1.22 m; 4.95 m; 2.44 mNiles p88 (74)"SWINGS 48 inches over the ways and 36 inches over the carriage. With a bed 16 feet 3 inches long it will turn 8 feet in length."
Niles 36 in latheswings 36 in over the ways, 27 in over the carriage; bed 12 ft 6 in turns 6 ft; weight 12,000 lb3.81 m; 1.83 m; 5.4 tNiles p87"With bed 12 feet 6 inches long it will turn 6 feet in length." "Weight, with 12-foot 6-inch bed, 12,000 lbs."
Niles 42 in latheswings 42 in over the ways, 32 in over the carriage; bed 12 ft 8 in turns 6 ft3.86 mNiles p88"With a bed 12 feet 8 inches long it will turn 6 feet in length."
Niles 50 in forge latheswings 50 in over the ways, 38 in over the carriage; 16 ft bed turns 7 ft 4 in; carries a forged shaft of 22 tons (the neighbouring 60 in forge lathe: 60 in over the ways, 46 in over the carriage, 16 ft bed turns 6 ft)4.88 mNiles p91"With 16-foot bed will turn 7 feet 4 inches between centers." "will carry between centers a forged shaft weighing 22 tons."
Niles 72 in lathe, bed width and depthbed 5 ft 4 in wide over the top and 24 in deep; carriage 5 ft 6 in; 18 ft bed turns 8 ft; swings 72 3/4 in over the ways, 54 in over the carriage1.63 m wide; 0.61 m deepNiles p94 (80)"The bed has great width, viz. : 5 feet 4 inches over the top, and depth of 24 inches."
Weights, Niles18 in lathe, 6 ft bed 2,400 lb; 22 in, 8 ft bed 3,300 lb; 26 in, 10 ft bed 7,400 lb; 30 in, 10 ft bed 8,000 lb; 36 in, 12 ft 6 in bed 12,000 lb1.1 t, 1.5 t, 3.4 t, 3.6 t, 5.4 tNiles p85, p87"Weight with 6-foot bed, 2400 lbs." ... "Weight with lo-foot bed, 8000 lbs."
Height of the centres above the floornot given by any of the three---

Sellers on the shear: "the lathe centres, being above the shear, and dependent entirely on the stiffness of the shear for their rigidity" (1877 text); a large Sellers lathe has three bearing ways in the bed and the heads are set over so that the line of centres falls between the centre bearing and the outer bearing at the back (1895 p136).

Cylinder boring machines and boring mills

FigureValueMetricPageQuote
Sellers locomotive cylinder borer6 in steel bar, driven at both ends of the cylinder; cutter heads for 10 to 22 in bores; independent slide-rests face both ends; bar draws out of the cylinder by hand or powerbar 0.15 m; bores 0.25 to 0.56 mSellers 1895 p83 (75); same text 1877 p72"6" steel boring-bar, driven at both ends of cylinder; independent slide-rests for facing off both ends of cylinder ; ... usual cutter-heads to bore from 10" to 22"."
Time on it3 1/2 h for the largest freight or express cylinder, against 9 h on the best earlier machine and "seldom less than thirteen hours on ordinary boring machines"-Sellers 1895 p82"in three and a half hours"
Sellers horizontal borer, compound tabletable 28 in by 48 in, cross traverse 24 in; bar 15 3/4 in above the table (OCR "15f", read as 15 3/4); heads for cylinders 7 1/2 to 14 in; bores cylinders to 32 in longtable 0.71 by 1.22 m; bar axis 0.40 mSellers 1895 p77, p76"Compound table, 28" wide, 48" long ... Height of boring-bar above table, 15f"." "It will readily bore cylinders 32" long"
Sellers horizontal borer, fixed tablespindle 4 in, stroke 30 in, spindle 16 in above the table; "air-brake cylinders up to say 15" or 16" in diameter"0.41 mSellers 1895 p75"the height of the centre of the spindle above the table is 16"."
Sellers triple borertable 5 ft by 4 ft 1/2 in; lower bar 21 in above the table1.52 m by 1.23 mSellers 1895 p81"The height from centre of lower boring-bars to table, 21"."
Sellers floor-boring machinespindle 4 in, stroke 30 in; spindle from 14 in to 6 ft 2 in above the floor-plate; upright traverses 4 ft 10 in0.36 to 1.88 mSellers 1895 p67 (59)"Minimum height of spindle above floor-plate, 14". Maximum height, 6' 2"."
Sellers vertical cylinder borercylinders 4 to 9 ft diameter and up to 10 ft long; bar 16 in; uprights 13 ft apart; driven by an 8 in by 8 in engine; operator on a platform atop reached by a ladderbar 0.41 m; 1.2 to 2.7 m diameter, 3.0 m long; uprights 3.96 mSellers 1895 p84 (76)"intended for boring cylinders from 4' to 9' diameter, and up to 10' long ... two massive uprights 13' apart ... The bar ... is 16" in diameter"
Vertical bar on a boring millbar 10 in by 12 ft, cylinders to 9 ft long; the cylinder is carried on a spider on the mill table, a second spider on its top flange carries the barbar 0.25 m by 3.66 mSellers 1895 p86"The bar shown is 10" in diameter by 12' long, and is capable of boring cylinders up to say 9' in length."
Niles No. 1cylinders 16 to 22 in; bar 8 in; tangent gearing; five feedsbar 0.20 mNiles p167 (153)"WILL bore cylinders from 16 to 22 inches diameter. The boring bar is 8 inches diameter."
Niles No. 2cylinder 28 in diameter and 39 in long including the sinking head; bar 9 in, drawn out by rack and pinion on the tail stockbar 0.23 m; 0.71 by 0.99 mNiles p167 (153)"arranged for cylinders 28 inches diameter and 39 inches long, including sinking head ... The boring bar is 9 inches diameter."
Niles No. 3stationary engine cylinders up to 36 in diameter and 60 in long, both ends faced at once; bar on rack and pinion; two saddles across the bed, clamped to it, hold the work0.91 m by 1.52 m (60 in)Niles p168 (154)"stationary engine cylinders up to 36 inches diameter and 60 inches long, boring and facing both ends at the same time." "Two saddles are provided, which extend across the bed and are clamped to it. These are for holding the work."
Niles No. 4cylinders up to 60 in and any length; bar between centres as in a lathe, head fed by screw at one end; bed set level with the floor; large face plate1.52 mNiles p168 (154)"will bore cylinders up to 60 inches diameter, and any length that may be desired ... mounted upon a heavy bed, which is set level with the floor."
Niles No. 5Corliss cylinders up to 42 in and 10 ft long, valve ports bored at the same setting; two bars, 7 in for cylinders up to 18 in and 12 in above that1.07 m, 3.05 m; bars 0.18 and 0.30 m = 2.8 and 4.9 vxNiles p169 (155)"capable of boring cylinders up to 42 inches diameter and 10 feet long. Two bars are furnished, one 7 inches diameter for cylinders up to 18 inches, the other 12 inches diameter for cylinders above that size."
Niles tool for flangesheads for "facing and turning the flanges of cylinders"-Niles p167"Heads are also furnished for facing and turning the flanges of cylinders."
Niles bar on a mill tablean upright bar with boring heads; "The bar is stationary, the cylinder revolving about it on the table of the Mill"-Niles p155 (141)"CYLINDER BORING BAR. An upright bar with suitable boring heads is frequently provided for boring large cylinders."
Boring and turning mills, Sellersmost common sizes bore and turn 5, 7, 8, 10, 12 and 16 ft; the 7 ft mill has a 5 ft 6 in table and 43 in under the cross-head1.68 m table; 1.09 mSellers 1895 p98, p97"Diameter of table, 5' 6". Greatest height under cross-head, 43"."
Boring and turning mills, Niles5 ft mill swings 60 in and takes work 28 in high; 6 ft mill swings 73 in, 36 in under the tool holders0.71 m; 0.91 mNiles p147, p149"SWINGS 60 inches diameter, and takes in work 28 inches high under the tool holders."
Bed length of a cylinder borernot stated in any of the three; Niles No. 4 "any length that may be desired"---

Planers

Sellers and Niles both name a planer by the width and height it takes (36 by 36), with the table length separate.

FigureValueMetricPageQuote
Sellers planer line20, 25, 30, 36, 42, 48, 54, 60, 72, 84, 120 in; each takes its size in width and in height; shortest table 3 ft (20 in), 4 ft (25 in), 5 ft (30 and 36 in), 6 ft (42 and 48 in), 7 ft (54 in), 14 ft (120 in)36 in = 0.91 m; 5 ft = 1.52 mSellers 1895 p196 (188)"Will Plane In Width ... In Height ... Shortest Length of Table" (columns read from the table; the 60 to 84 in rows lost their lengths in OCR)
Niles planer list26 by 26 in, tables 6 to 10 ft, 7,000 to 9,000 lb; 32 by 32, 6 to 14 ft, 11,000 to 16,000 lb; 38 by 38, 8 to 16 ft, 16,000 to 24,000 lb; 44 by 44, 10 to 18 ft, 23,500 to 34,000 lb; 48 by 48, 10 to 20 ft, 28,000 to 42,000 lb26 in = 0.66 m; table 1.8 to 6.1 m; 3.2 to 19 tNiles p105 (91)read from the page image: "Size. Length of Table. ... Weight." rows "32 x 32 inches. 6 feet ... 11,000 lbs."
Niles large planers54, 60, 72, 84, 96 and 120 in; tables 10 to 24 ft; 54 by 54 by 10 ft 32,000 lb; 120 by 120 by 16 ft 125,000 lb1.37 to 3.05 mNiles p107 (93)read from the page image: "List of Planers. LARGE SIZES."
Sellers 62 in by 18 in locomotive-frame planertable 4 ft 8 in wide with a 3 in top plate; 5 ft 3 in between uprights; 19 in from table top to under-side of cross-head; plane 35 ft longtable 1.42 m wide; 0.48 m under the railSellers 1895 p206 (198)"Table 4' 8" wide, with top plate 3" thick. Width between uprights, 5' 3". Height from top of table to underside of cross-head, 19"."
Sellers 96 in planerstationary table 24 ft long and 8 ft wide7.3 m by 2.44 mSellers 1895 p209"With Stationary Table 24 Feet Long, 8 Feet Wide."
Sellers planing, shaping and slotting machinebed 38 ft by 8 ft 9 1/2 in; saddle 14 ft; uprights 16 ft; planes 24 ft, slots 12 ft, shapes 6 ft11.6 m; uprights 4.9 mSellers 1895 p210 (202)"Length of bed, 38'; width of bed, 8' 9J"; length of saddle on the bed, 14'; height of uprights, 16'."
Cutting and return speedusual speed of cut 18 ft per minute, table return 72 ft per minute (four times)5.5 m/min, 21.9 m/minSellers 1895 p195 (187), p199"Usual speed of cut, 18 feet per minute; return speed of table, 72 feet per minute."
Table height above the floor, strokeneither is given; a stroke is the table length plus the work, not a stated figure---

Shapers

FigureValueMetricPageQuote
Sellers 9 in shaperstroke 0 to 9 in; bar adjustable 13 in more; saddle moves 36 in on the bed; table to shaping bar 11 in at most; table overhang 14 1/2 in; tables 42 in edge to edge0.23 m stroke; saddle 0.91 mSellers 1895 p183 (175)"Stroke adjustable from 0 to 9". Shaping bar adjustable 13" in addition to the stroke. Movement of saddle on bed, 36". ... Greatest distance between table and shaping bar, 11"."
Sellers 12 in shaperstroke 0 to 12 in; saddle 48 in; table to bar 13 1/2 in; overhang 19 in; tables 58 in edge to edge0.30 m stroke; saddle 1.22 mSellers 1895 p184 (176)"Stroke adjustable from 0 to 12 inches, with Whitworth motion ... Movement of saddle on bed, 48"."
Sellers 16 in shaperstroke 0 to 16 in; bar adjustable 25 in more; saddle 66 in; table to bar 16 1/4 in; overhang 23 in; tables 77 in edge to edge0.41 m stroke; saddle 1.68 mSellers 1895 p185 (177)"Stroke adjustable from 0 to 16", with Whitworth motion ... Movement of saddle on bed, 66"."
Sellers double shapertwo 12 in machines on a 13 ft base; 18 ft between the outer tables3.96 mSellers 1895 p186"Two 12" shaping machines on one base, 13' long."
Niles 24 in shapercutter bar 24 in stroke; bed 8 ft 4 in; saddle traverse 70 in; bar 63 in long; tables rise 21 in; "the heaviest and most powerful Shaping Machine built in this country"0.61 m stroke; bed 2.54 m; 1.78 m saddleNiles p127 (113)"The cutter bar has 24 inches stroke ... The bed is 8 feet 4 inches long. The saddle has 70 inches traverse on the bed." "The tables have a vertical adjustment of 21 inches."
Niles slotters10 in slotter: bar stroke 10 1/4 in, table 26 in round, takes 48 in; 14 in: table 30 in round; 18 in: table 42 in round, takes 78 intable 0.66 m, 0.76 m, 1.07 mNiles p129 (115 to 116)"The table is 26 inches diameter. It has 20 inches longitudinal and 17 inches transverse traverse."
Machine height above the floornot given---

Drilling presses

FigureValueMetricPageQuote
Sellers 36 in vertical drilloverreach 18 in from spindle to column face; table 26 in by 18 in or 26 in round on a swinging bracket; spindle stroke 12 in; lower bearing 5 ft above the floorthroat 0.46 m; table 0.66 by 0.46 m; bearing 1.52 mSellers 1895 p31, p32 (23, 24)"Plain table, 26" long by 18" wide; or circular table, 26" diameter, carried on swinging bracket ... Stroke, 12". Lower bearing 5' above floor." "overreach of 18 inches from the centre of the spindle to the face of the column"
Sellers 45 in vertical drilloverreach 22 1/2 in; compound table 22 in square, or round table 32 in; table travel 24 in; spindle bearing 5 ft above the floor; stroke 17 1/2 inthroat 0.57 m; table 0.56 m or 0.81 m; stroke 0.44 mSellers 1895 p33, p34"Vertical adjustment of table, 24". Height of spindle bearing above floor, 5'." "Overreach, 22
Sellers 96 in radial drillreach 83 in through the centre of the arm's rotation; spindle stroke 17 in (OCR); 67 in from the floor to the spindle nose at most; work table 24 in square and 30 in high2.1 m; table height 0.76 m; nose 1.70 mSellers 1895 p51"Greatest height from floor to nose of spindle, 67". ... Slotted table for work, 24" square, 30" high."
Sellers traverse drillcross-head 52 in from the floor; table 24 in square; reach 36 in by 24 incross-head 1.32 mSellers 1895 p53"Height of cross-head from floor, 52". Overreach of spindle, 10"." "so that the space covered at one setting is 36" x 24"."
Niles No. 2 vertical drilldrills to the centre of 24 in; spindle traverse 8 in; end of spindle to base 54 in; table lifts 20 in and swings round the columnthroat 0.61 m; base 1.37 mNiles p193 (179)"DRILLS TO CENTER OF 24 INCHES ... spindle has a traverse of 8 inches ... Distance from end of spindle to base, 54 inches."
Niles No. 3 vertical drillcentre of 30 in; traverse 12 in; end of spindle at full hoist to base 4 ft 10 in; table 30 in diameter, lifts 15 in; head adjusts 24 in; drills to 3 in, bores to 10 inthroat 0.76 m; base 1.47 m; table 0.76 mNiles p193"DRILLS TO CENTER OF 30 INCHES." "Distance from end of spindle (at full hoist) to base, 4 feet 10 inches." "The table is 30 inches diameter. It is raised and lowered by screw ... lift of 15 inches."
Niles No. 5 and No. 6 vertical drillscentre of 50 in, traverse 15 in, spindle end to base 56 in; No. 6 centre of 60 in, traverse 18 in, base 58 inthroat 1.27 m and 1.52 mNiles p195"DRILLS TO CENTER OF 50 INCHES." "Distance from end of spindle to base, 56 inches."
Niles No. 3 radial drillarm 7 ft long, column 9 ft high; base plate to the spindle end 6 ft 5 in with the arm at the top of the column ; faces cylinder heads and flanges of pumpscolumn 2.74 m; 1.96 mNiles p203"ARM, 7 FEET LONG. COLUMN, 9 FEET HIGH." "the distance between the base plate and the end of the drill spindle is 6 feet 5 inches"
Drill table height above the floor, bench drillsnot given as such; table heights follow the base-to-spindle figures above---

Engravings with a man beside a machine

None found. The plates read for this note (Sellers 1895 Plates 42 and 48 at pp85 and 97; Niles No. 2 cylinder borer at p166) show the machine on its own. The one human cue in print is on the Sellers vertical cylinder borer: the operator stands on a platform at the top of the uprights, "accessible by a ladder on one of the uprights" (Sellers 1895 p84). The plates were not all viewed; the catalogues carry about 150 plates each.

What period shops used to bore and turn large steam cylinders

Stated in the catalogues:

  • Boring on a cylinder borer. The barrel is bored, not turned inside the lathe's usual way: a steel bar lies between head and tail stock (as in a lathe), a cutter head rides on the bar and is fed by a screw, and the bar is driven by tangent (worm-type) gearing. Niles No. 3 takes engine cylinders to 36 in by 60 in, No. 4 to 60 in by any length, No. 5 to 42 in by 10 ft (Niles pp167-169).
  • Bar sizes. 6 in for 10 to 22 in locomotive bores (Sellers); 8 in for 16 to 22 in and 9 in for a 28 in bore (Niles); 7 in up to an 18 in bore and 12 in above that (Niles No. 5); 16 in for the vertical borer of 4 to 9 ft.
  • How the cylinder is held. Lying on two saddles that "extend across the bed and are clamped to it" (Niles No. 3); on a table between two face plates, the bar driven at both ends (Sellers); standing upright on a mill table with a stationary vertical bar through it for the large sizes (Niles bar attachment, Sellers 10 in by 12 ft bar).
  • Ends and flanges. Slide-rests on the face plates or on sleeves "face off both ends of cylinder" and turn the flanges while the bar bores; the flanges and the counterbore at the end are the turned work (Sellers 1895 p82; Niles p167).
  • Outsides. Neither catalogue says the barrel's outer surface was turned. The only turning named on a cylinder is the flanges and, in the Sellers vertical borer, "turning off flanges of cylinders up to 10' in diameter". Niles lists a "Cylinder Lathe" for turning printing-press cylinders and paper-machine rolls, not steam cylinders (Niles p229). Not documented: a turned cast-iron steam-cylinder exterior.
  • Why. "one cut with a fine feed takes out the greater part of the metal"; a roughing cut with a fine feed and finishing cuts with a broad feed (Sellers 1895 p82). A cylinder 22 in by about 3 ft took 3 1/2 h on the special machine against 9 to 13 h on an ordinary one.

INFERRED: the cast barrel's outside stays as cast and only the flange faces, bolt-circle faces and the bore are machined.

Gaps

  • Height of lathe centres, bed top, planer table, shaper table and boring-bar axis above the floor: none of the three says.
  • Lathe bed width: only the Niles 72 in lathe (5 ft 4 in wide over the top, 24 in deep). Nothing for 36 to 60 in lathes.
  • Sellers weights: not given for lathes, planers or borers. Niles has weights for lathes to 36 in and for planers.
  • Table width of a planer: given only for the 62 by 18 in frame planer (4 ft 8 in) and the 96 in (8 ft); otherwise the table is only the width of work it planes.
  • Bed length of a cylinder borer, and the length of the Sellers locomotive borer: not stated.
  • Anything before 1873: no Whitworth, Nasmyth, Armengaud or Fairbairn tool tables were found. Searches on archive.org for Whitworth tools, Nasmyth and the Armengaud "Practical Draughtsman" returned no scan with tables; Putnam and Bement catalogues returned one 1893 Bement catalogue (a 3,000 character OCR with no tables, not downloaded) and Hill, Clarke 1893 and Gould and Eberhardt 1893, which are later than the window.
  • Marine cylinders above 60 in and steam cylinders in 1850 to 1870 shops: the evidence here is the 1891 catalogues and a 1876 treatise.
  • Engravings with a man: none found in the pages looked at.